VisualizationScrunchie Box SVG, Two Section Hair Accessory Organizer, Simple Laser Cut Comb Holder DXF
A simple two-section plywood box for scrunchies, clips and a comb, 300 × 180 × 90 mm (11.81 × 7.09 × 3.54 in), with a 76 mm front and gently sloped sides. The free download contains SVG and DXF for 3, 4, 5 and 6 mm plywood; it has just 6 parts held together by tabs and slots.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 300 × 180 × 90 mm (11.81 × 7.09 × 3.54 in)
- Parts
- 6
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 980 × 282 mm
- Cut length
- 4.46 m
- Est. time, 10 W diode (3 mm)
- 14 min 52 s
- Est. time, 40 W CO2 (3 mm)
- 6 min 12 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the file for your plywood and cut the divider slot on an offcut to check the tab fit, especially on 5 or 6 mm stock.
- 02Cut the 6 parts in one or two sheets.
- 03Slot the sides into the base, add the back, push the divider in and finish with the front wall.
- 04Sand the top edges, apply oil or lacquer and fill the big section with scrunchies and the narrow one with a comb.
The simplest box in the set
With 6 parts and one divider, this is the quickest hair organizer to cut and build, which makes it a good first project for a new laser. The single divider sits off-centre and gives you a big section and a narrow one. In the big section go headbands, scrunchies and a couple of claw clips; the narrow one is just right for a long comb standing on edge with a bundle of bobby pins beside it.
The slope is gentle: the back is 90 mm and the front 76 mm, so the box reads almost like a straight-sided tray but still shows its contents from the front.
Cutting and building it
The 3 mm file is estimated at about 14 min 52 s on a 10 W diode, about 6 min 12 s on a 40 W CO2 and about 2 min 58 s on a 100 W CO2. With so few parts, even a 6 mm version on a diode is realistic if you are patient with passes, but test one slot first: thick plywood often has a slight taper on a diode, which makes tabs tight at the bottom. The layout is 980 mm long; split it in two on a small bed.
Sides into base, back on, divider in, front on. That is the whole build. Add glue only if you want it permanent.
Selling and gifting
- A beginner kit item: sell the cut parts flat-packed for kids to assemble.
- A dorm or travel-size organizer for a few favourite accessories.
- Batch-cut a dozen for a market table; the low part count keeps the price low.
Questions about this file
Is this a good first laser project?
Yes. It has only 6 parts and one divider, so assembly takes a minute and a bad fit is easy to spot.
Does a long comb fit in the narrow section?
Yes, a standard wide-tooth comb stands on its edge in the narrow section, with room for bobby pins next to it.
Can I scale it into a bigger storage box?
Yes, but reset the slot width to your material after scaling. Proportional scaling also changes the slots, and then the tabs no longer fit.
Can I cut it in acrylic?
Yes, use the file that matches the acrylic thickness. Measure the sheet first, since cast acrylic is rarely exact.
Can I pack it flat for kids to build?
Yes, the 6 parts press together without tools or glue, so it works as a simple build-it-yourself kit.
Similar files
