VisualizationHeadband and Hair Clip Organizer SVG, Wooden Hair Accessory Box With Side Pockets, Laser Cut DXF
A plywood organizer for headbands and hair clips, 320 × 220 × 80 mm (12.60 × 8.66 × 3.15 in), with one large bay on the left and three small pockets stacked front to back on the right; the front is 64 mm and the sides slope. The free download has SVG and DXF for 3, 4, 5 and 6 mm plywood, 8 tab-and-slot parts.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 320 × 220 × 80 mm (12.60 × 8.66 × 3.15 in)
- Parts
- 8
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,100 × 312 mm
- Cut length
- 5.93 m
- Est. time, 10 W diode (3 mm)
- 19 min 46 s
- Est. time, 40 W CO2 (3 mm)
- 8 min 14 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Pick the file for your plywood (3, 4, 5 or 6 mm) and cut one slot on scrap to see that the long divider tab slides in firmly.
- 02Cut the 8 parts; the base, back and front are 320 mm long, so place them first when splitting sheets.
- 03Fit sides and back to the base, add the long divider, then the two short cross dividers on the right, and close with the front.
- 04Sand, oil or lacquer the box, then stand headbands in the big bay and sort clips into the three side pockets.
Big bay, three side pockets
Here the split is lengthwise. One long divider runs from front to back about two thirds of the way across, leaving a large bay on the left. That bay holds the bulky items: a padded headband and a braided one standing against the back wall, two satin scrunchies and a wide comb laid across the front. On the right, two short cross dividers make three stacked pockets: a matte claw clip at the back, a clear clip in the middle and gold bobby pins in front. Because the right column steps down with the slope, the smallest pocket is the easiest to reach.
What to cut it from
Birch plywood in 3 mm cuts fastest: the 3 mm file takes about 19 min 46 s on a 10 W diode, about 8 min 14 s on a 40 W CO2 and about 3 min 57 s on a 100 W CO2. The 5 and 6 mm files give a chunkier box but need a CO2 laser or slow multi-pass cutting on a diode. Light MDF works too if the box will live in a bedroom rather than a bathroom. The layout is 1100 mm long, so most desktop machines need it split onto two sheets.
Assembly, care and gift ideas
Put the sides and back into the base, then slide in the long divider, then the two short cross dividers on the right. Front panel goes on last. No glue is needed, though a drop on the long divider makes the whole box stiffer. For a bathroom counter like the one in the photo, seal the box with oil or clear lacquer and wipe it with a dry cloth.
People with a lot of headbands are the main audience; tag your listing for headband storage. It also works as a gift for a bride or bridesmaid, filled with matching pins and clips.
Questions about this file
How many headbands fit in the large bay?
Three or four standard headbands stand side by side, with room in front for scrunchies and a comb.
Can I move the long divider to make the bay smaller?
Only by editing the slots in the base, front and back. Keep the slots the same width as your plywood so the divider still locks.
Is this safe to keep on a bathroom counter?
Yes, once it is sealed. Use a waterproof finish like polyurethane or hard wax oil and avoid standing it in puddles.
What thickness suits a gift box like this?
4 mm plywood gives a solid feel without much extra weight; 3 mm is lighter and quicker to cut.
Can I engrave initials for a bridesmaid gift?
Yes, add the initials yourself on the front panel as an engrave layer. The file itself only contains cut lines.
Similar files
