VisualizationTiered Jewelry Tray SVG, Stepped Jewelry Display DXF, Three Row Earring and Bracelet Organizer Laser Cut File
A three-tier stepped jewelry tray: two full-width cross dividers of different heights create three rows that step down from the back to a low 32 mm front, so earrings sit in front, bracelets in the middle and sunglasses and a watch at the back. It measures 360 × 230 × 70 mm (14.17 × 9.06 × 2.76 in), uses 7 tab-and-slot pieces and comes as a free SVG and DXF download for 3, 4, 5 and 6 mm plywood.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 360 × 230 × 70 mm (14.17 × 9.06 × 2.76 in)
- Parts
- 7
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,200 × 312 mm
- Cut length
- 6.40 m
- Est. time, 10 W diode (3 mm)
- 21 min 21 s
- Est. time, 40 W CO2 (3 mm)
- 8 min 54 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the file for your plywood and cut one cross-divider slot on scrap to confirm the fit.
- 02Cut the seven parts over two or three sheets, keeping the 360 × 230 mm base whole.
- 03Insert the 54.7 mm divider at the back and the 43.1 mm divider in front, then fit the back wall, sloped sides and 32 mm front.
- 04Sand the stepped edges, oil the tray and arrange earrings in front, bracelets in the middle and larger items at the back.
How the three tiers work
There are no front-to-back dividers in this tray. Instead, two long cross dividers run the full 360 mm width at different heights: 54.7 mm for the rear one and 43.1 mm for the front one. With a 70 mm back wall and a 32 mm front, the rows step down like theatre seating, and each row is visible over the one in front.
That makes it ideal for sorting by size. Small pieces (pearl studs, crystal earrings, rings) go in the lowest front row. Bracelets lie in the middle row, and the deep back row takes sunglasses and a watch on a mesh strap, as in the photo.
Cutting
Seven pieces: front, back, two sloped sides, base and two cross dividers. For the 3 mm file allow about 21 min 21 s on a 10 W diode, about 8 min 54 s on a 40 W CO2, or about 4 min 16 s on a 100 W CO2. The nested layout is 1200 × 312 mm, so you will need two or three sheets on a desktop machine. The base is the biggest single piece at 360 × 230 mm.
Assembly and finishing
Slot both cross dividers into the base first, taller one at the back, then add the back wall, the sides and the low front. Make sure the dividers are in the right order: if they are swapped, the steps go the wrong way. Glue is not required.
Finish with clear oil and a light sanding of the stepped edges, which catch the eye when the tray is empty. Strips of felt in the front row help rings stand upright.
Because it looks like a little display stand, this tray works well as a teacher or bridesmaid gift with a pair of earrings already set in the front row.
Questions about this file
Can I add dividers to split the rows?
The file has none, but you can draw short dividers yourself. Make the slots exactly as wide as your plywood so they lock in like the rest of the tray.
What goes in each tier?
Use the low front row for rings and stud earrings, the middle one for bracelets and the deep back row for sunglasses, watches or a phone.
Does the 32 mm front let rings fall out?
No, the front still rises 32 mm above the base, which keeps rings in. Felt strips in that row make them even steadier.
Can I seal it for a bathroom shelf?
Yes. Two coats of water-based polyurethane on all faces, including the base underside, protect it from humidity and splashes.
Which thickness gives the cleanest steps?
3 or 4 mm keeps the step edges thin and neat. Thicker plywood works but makes the tiers look heavier.
Similar files
