VisualizationHair Clip Organizer SVG, Claw Clip Holder With Scrunchie Bin, Laser Cut Wooden Hair Tray DXF
A plywood hair clip organizer, 360 × 200 × 80 mm (14.17 × 7.87 × 3.15 in), with four small pockets along the back and one long open bin across the front, plus a 60 mm sloped front. Free SVG and DXF files for 3, 4, 5 and 6 mm plywood; 9 parts that slot together with tabs.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 360 × 200 × 80 mm (14.17 × 7.87 × 3.15 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,140 × 292 mm
- Cut length
- 6.76 m
- Est. time, 10 W diode (3 mm)
- 22 min 31 s
- Est. time, 40 W CO2 (3 mm)
- 9 min 23 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Use the SVG or DXF for your plywood thickness; cut one short divider slot on scrap first to check the fit.
- 02Cut the 9 pieces, moving the 360 mm base onto its own sheet if the full layout does not fit.
- 03Assemble the shell, insert the full-width cross divider, then the three back dividers, then the low front panel.
- 04Sand the pocket rims smooth, apply matte lacquer and put clips in the back pockets and scrunchies in the front bin.
Four pockets and one long bin
This is a wide box (360 mm) with a clear split of jobs. A cross divider runs the full width, and three short dividers cut the back row into four pockets, each about the size of one or two claw clips. Use them for a cream claw clip, a tortoiseshell one, a bundle of bobby pins and a small pink clip. The front row stays open from side to side, so bulky things fit: two or three scrunchies, a headband lying on its side and a wooden comb.
The front is only 60 mm high, the lowest point of the slope, so the long bin is easy to dig into.
Cutting time and bed size
Estimated for the 3 mm file: about 22 min 31 s on a 10 W diode, about 9 min 23 s on a 40 W CO2, about 4 min 30 s on a 100 W CO2. A diode can cut 3 mm in one or two passes; 6 mm birch may need four or more, so a CO2 is the better choice for the thicker versions. The parts sit in a 1140 mm strip; on a smaller machine cut the base alone and group the rest.
Assembly, finish and gifts
Base, sides, back first. Then the long cross divider, then the three back dividers, which are full height and sit between the cross divider and the back wall. Finish with the front panel. Sand the top edges, especially the pocket rims, so they do not snag satin scrunchies. A clear matte lacquer keeps the light birch colour.
Fill the four back pockets with clips in matching colours and the front bin with scrunchies for a ready gift box. It also works as a display tray at a market stall selling hair accessories.
Questions about this file
What fits in the long front bin?
Scrunchies, one or two headbands lying on their side and a comb. It runs the whole width of the box.
Can I add a fifth pocket at the back?
You would need to add a slot to the cross divider and back wall and cut one more divider. Keep the new slot width equal to your plywood thickness.
Is 3 mm plywood strong enough?
Yes, for hair accessories 3 mm birch is plenty, and it is the fastest version to cut on a diode laser.
Can this be cut from MDF?
Yes, MDF cuts cleanly, but paint or seal it because raw MDF edges absorb moisture quickly.
How do I keep the pocket rims from snagging satin?
Sand the top edges with 180 and then 240 grit and seal them. A smooth, sealed edge will not pull threads from satin scrunchies.
Similar files
