VisualizationJewelry Tray SVG, Ring and Earring Slot Organizer DXF, Straight Wall Vanity Jewelry Box Laser Cut File
A straight-walled jewelry tray with one large bay on the left and a column of three narrow slots on the right for rings, drop earrings and studs. It measures 360 × 210 × 70 mm (14.17 × 8.27 × 2.76 in), is cut from 8 pieces joined by tabs and slots, and the free download includes SVG and DXF versions for 3, 4, 5 and 6 mm plywood.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 360 × 210 × 70 mm (14.17 × 8.27 × 2.76 in)
- Parts
- 8
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,160 × 292 mm
- Cut length
- 6.19 m
- Est. time, 10 W diode (3 mm)
- 20 min 37 s
- Est. time, 40 W CO2 (3 mm)
- 8 min 36 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Pick the file for your plywood and cut one cross-divider slot on scrap to check the tab is snug but not tight.
- 02Cut all eight pieces, splitting the 1160 mm layout over two or three sheets if needed.
- 03Fit the two short cross dividers to the long divider, set it on the base and add the four 70 mm walls.
- 04Sand the top edges, lacquer the tray and line the three narrow slots with felt for rings and earrings.
One big bay, three narrow slots
A single divider runs from back to front about two thirds of the way along, leaving a large open bay on the left. Two short cross dividers split the right-hand strip into three slim slots stacked one behind the other. The slots are shallow from front to back, which is what you want for rings and earrings: they stay in a line instead of piling up.
In the photo the big bay holds sunglasses, a watch, a beaded bracelet and a bangle, while the slots carry crystal drop earrings, two rings and a pair of pearl studs. All four walls are 70 mm, so this tray also works inside a wide dresser drawer.
Cut time and layout
Eight parts in total. For the 3 mm file the job takes about 20 min 37 s with a 10 W diode, about 8 min 36 s with a 40 W CO2 and about 4 min 07 s with a 100 W CO2. The nested layout is 1160 × 292 mm. If your bed is around 400 × 400 mm, cut the base on one sheet and the walls and dividers on two more.
Thin 3 mm stock is the quick option for a diode laser. The 5 and 6 mm files give a heavier, more solid tray but take several passes on a diode.
Putting it together
Hook the two cross dividers onto the long divider, stand the assembly on the base, then add the back, the sides and the front. Tabs and slots keep it square without glue; use a drop of wood glue if the tray will travel. Finish with a clear lacquer, or line the three slots with thin felt so rings do not slide.
Fill it with a watch and a pair of earrings as an anniversary present, or sell it as a "first jewelry tray" for teenagers.
Questions about this file
What are the three narrow slots on the right for?
They are meant for rings, drop earrings and studs, one type per slot, so small pieces stay in rows instead of a tangle.
Will it fit in a dresser drawer?
It is 70 mm tall with straight walls, so it fits most dresser drawers that are at least 75 mm deep inside and 360 × 210 mm in area.
Can I make it in 4 mm plywood?
Yes, the download includes a 4 mm file with slots sized for that thickness. Measure your sheet first, since 4 mm plywood is often slightly thinner.
How do I stop rings sliding around?
Glue thin felt or velvet into the three slots. It also protects soft gold from scratches.
Is engraving included in the file?
No, the file contains cut lines only. You can add a name or initials to the front panel yourself before cutting.
Similar files
