VisualizationHair Accessory Organizer SVG, Scrunchie and Headband Box Laser Cut File, Wooden Hair Clip Tray DXF
A laser-cut plywood organizer for hair accessories with one wide section and two narrow ones, measuring 320 × 180 × 90 mm (12.60 × 7.09 × 3.54 in) with the front wall lowered to 68 mm. The free download has SVG and DXF files for 3, 4, 5 and 6 mm plywood, 7 pieces that lock together with tabs and slots.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 320 × 180 × 90 mm (12.60 × 7.09 × 3.54 in)
- Parts
- 7
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,020 × 282 mm
- Cut length
- 5.25 m
- Est. time, 10 W diode (3 mm)
- 17 min 30 s
- Est. time, 40 W CO2 (3 mm)
- 7 min 18 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Pick the SVG or DXF that matches your plywood (3, 4, 5 or 6 mm) and cut a single divider slot on scrap to check that the tab fits snugly.
- 02Cut all 7 parts; on a bed shorter than 1020 mm, move the base and back to a second sheet.
- 03Fit the two sloped sides into the base, add the tall back wall, slide in both dividers and finish with the low front.
- 04Sand the burnt edges lightly, wipe on oil or clear lacquer, then load headbands on the left and clips and pins on the right.
What fits inside
This box splits 320 mm of width into three parts. The left half is one open bay, wide enough to stand two or three headbands against the back wall with a pile of scrunchies in front of them. The two slim sections on the right take the small things that usually get lost: claw clips in one, a wide-tooth comb and a row of bobby pins or pearl pins in the other. The back wall is 90 mm tall and the sides slope down to a 68 mm front, so you can see every clip from above without lifting anything out.
It sits nicely on a dresser or vanity top and is shallow enough (180 mm deep) for a wide bathroom drawer.
Cutting the seven parts
There are only 7 parts: front, back, two sloped sides, base and two dividers. The 3 mm layout is 1020 mm long, so on a small bed split it onto two sheets: base and back on one, the rest on the other. Estimated time for the 3 mm file is about 17 min 30 s on a 10 W diode, about 7 min 18 s on a 40 W CO2 and about 3 min 30 s on a 100 W CO2. If your diode needs extra passes, the 5 and 6 mm versions will take noticeably longer.
Push the sides into the base first, add the back, then drop the two dividers into their slots before closing the front. The joints hold without glue; add a little wood glue if the box will be carried around.
Gift and shop ideas
- Fill it with three scrunchies, two claw clips and a comb for a ready-made birthday gift.
- Offer it in a light and a dark stain as a pair for sisters or a mother and daughter.
- Sell it at craft fairs next to hair accessory sellers, who often need display trays.
Questions about this file
Will a padded headband fit in the wide section?
Yes. The left bay takes up roughly half of the 320 mm width, which leaves room for two or three padded or braided headbands standing on edge.
Can I make it bigger for a whole family?
You can scale the outline, but keep the slot width equal to your real sheet thickness or the tabs will not lock. Scaling a 3 mm file by 120% without fixing the slots gives 3.6 mm slots that wobble.
Which thickness works best for a three-section hair box?
3 or 4 mm birch plywood keeps it light and quick to cut. Choose 5 or 6 mm if you want a heavier feel and have a CO2 laser.
Can I cut it from acrylic?
Yes, the 3 mm file works with 3 mm cast acrylic. Measure your acrylic first, because sheets often vary by a few tenths of a millimetre.
What finish suits a bedroom vanity?
Clear matte lacquer or a thin coat of furniture oil keeps the pale birch colour and stops scrunchie fabric catching on raw fibres.
Similar files
