VisualizationSmall Skincare Box SVG, Two Section Cosmetic Organizer Laser Cut File, Beginner Plywood Tray DXF
A small two-section skincare box with a sloped front, supplied as SVG and DXF with separate files for 3, 4, 5 and 6 mm plywood. It measures 280 × 170 × 110 mm (11.02 × 6.69 × 4.33 in), has only 6 pieces and one divider, and its front wall is 55 mm high. It is held together by tabs and slots and is free to download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 280 × 170 × 110 mm (11.02 × 6.69 × 4.33 in)
- Parts
- 6
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 920 × 292 mm
- Cut length
- 4.25 m
- Est. time, 10 W diode (3 mm)
- 14 min 11 s
- Est. time, 40 W CO2 (3 mm)
- 5 min 55 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Pick the file for your sheet thickness and test the divider slot on an offcut.
- 02Cut the 6 parts: front, back, two sloped sides, base and one divider.
- 03Push the divider into the base, add the 110 mm back, fit both sides, and finish with the 55 mm front.
- 04Sand lightly, finish with oil or lacquer, and put pads in the narrow section and everything else in the wide one.
The simplest box in the set
With six parts and a single divider, this is the quickest skincare box to cut and assemble here, which also makes it a good first project for a new laser. The divider sits off-centre and creates one wide section and one narrow one.
In the photo the wide section holds three sheet masks, a large and a small cream jar, and two serum bottles, a clear one and an amber one. The narrow section on the right is just wide enough for a stack of cotton pads. If your routine is a few products and some pads, two sections are all you need, and nothing gets lost in small cells.
Fast to cut
The 3 mm file is laid out on a 920 × 292 mm sheet and cuts in about 14 min 11 s on a 10 W diode, about 5 min 55 s on a 40 W CO2 and about 2 min 50 s on a 100 W CO2, the shortest times in this category. A 10 W diode handles 3 mm in one or two passes; for 5 or 6 mm, plan several passes or use a CO2. On a short bed, cut the base and the back separately from the other four pieces.
Assembly takes a minute: divider into the base, then the back, the two sloped sides and the front.
Ideas for selling
The low part count keeps your cost per box down, so this one works as an entry-price listing or a craft-fair item. Offer it in natural birch, in white, or with a customer's initials added to the front. A pair in different stains makes a simple gift set.
Questions about this file
Is this a good first laser project?
Yes. Six parts, one divider and short cutting times make it easy to cut, check and assemble in one session.
What goes in the narrow section?
It is sized for a stack of round cotton pads, but cotton buds, a lip balm or a slim tube also fit.
Can I cut it from 3 mm MDF?
Yes, use the 3 mm file and test a slot first. Paint or seal MDF so cream and water do not stain it.
Can I move the divider to the middle?
Move the divider slots in the base and walls in your design software; keep the slot width equal to your sheet thickness.
Do I need glue?
No glue is needed to use it. Add wood glue if you want to ship it assembled.
Similar files
