VisualizationHair Clip Organizer SVG, Headband and Scrunchie Box With Stacked Pockets, Laser Cut Vanity Tray DXF
A plywood hair organizer, 380 × 200 × 80 mm (14.96 × 7.87 × 3.15 in), with three columns: a scrunchie bin on the left, a wide headband bay in the middle and three stacked pockets for clips and pins on the right; the front is 40 mm. The free files are SVG and DXF for 3, 4, 5 and 6 mm plywood, 9 parts with tab-and-slot joints.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 380 × 200 × 80 mm (14.96 × 7.87 × 3.15 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,180 × 292 mm
- Cut length
- 6.53 m
- Est. time, 10 W diode (3 mm)
- 21 min 45 s
- Est. time, 40 W CO2 (3 mm)
- 9 min 04 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Measure your plywood, open the matching file and cut a single long-divider slot in a scrap strip as a fit test.
- 02Cut the 9 parts and mark the two small cross dividers so you can tell the taller back one from the lower front one.
- 03Fit sides and back to the base, add the two long dividers, then the two cross dividers in the right column, then the front.
- 04Sand the small pockets, apply lacquer and fill the left bin with scrunchies, the middle with headbands and the right pockets with clips.
Three columns, five spaces
Two long dividers split the 380 mm width into three columns. The left column is a deep bin for scrunchies; the middle one is the widest and takes headbands lying across it with a comb in front. The right column is divided by two short cross dividers into three stacked pockets that step down toward you: a cream claw clip at the back, a tortoiseshell clip in the middle and bobby pins in front. Small clips get their own place, while the big items keep the open bays.
At 200 mm deep it is slimmer than most of the large boxes in this range, so it suits a narrower dressing table or a bedroom vanity.
Cutting and building
Cut time for the 3 mm file is about 21 min 45 s on a 10 W diode, about 9 min 04 s on a 40 W CO2 and about 4 min 21 s on a 100 W CO2. Stick with 3 or 4 mm on a diode; the 5 and 6 mm files give a heavier box but need a CO2 or extra passes. The layout is 1180 mm long, so most hobby users will split it onto two sheets.
Assembly: base, sides, back, the two long dividers, then the two small cross dividers in the right column, and the 40 mm front. The cross dividers are different heights to follow the slope; check which goes at the back before pushing them in. No glue needed.
Sanding, lacquer and buyers
Sand inside the small pockets with a folded strip of sandpaper. A clear water-based lacquer keeps the pale colour shown in the photo, next to a pink wall and a round mirror. Sell it as a vanity organizer for teens, or fill it with a matching set of clips and scrunchies as a gift.
Questions about this file
Why are the two small cross dividers different heights?
They follow the slope of the sides, so the back one is taller than the front one. Put the taller one nearer the back wall.
What fits in the three stacked pockets?
One claw clip per pocket, or bobby pins, snap clips and small hair ties.
Can I scale it to fit a drawer?
Yes, but set each slot back to your plywood thickness after scaling, or the dividers will not lock in.
Which material looks best for a teen gift?
Birch plywood with clear lacquer or a pastel paint. Acrylic in the matching thickness also works.
Do I need glue?
No, the tabs hold it firmly. Glue only if you want it permanent.
Similar files
