VisualizationSquare Pad Organizer SVG, Deep Tampon and Liner Box, Countertop Feminine Care Caddy Laser DXF
A deep, nearly square organizer with a wide center bay for pads and two side columns, each split in two, for tampons, panty liners and wipes. It comes as SVG and DXF for 3, 4, 5 and 6 mm plywood, measures 300 × 240 × 110 mm (11.81 × 9.45 × 4.33 in), and assembles from 9 tab-and-slot parts into five compartments with a sloped front. It is a free download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 300 × 240 × 110 mm (11.81 × 9.45 × 4.33 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,100 × 362 mm
- Cut length
- 6.87 m
- Est. time, 10 W diode (3 mm)
- 22 min 55 s
- Est. time, 40 W CO2 (3 mm)
- 9 min 33 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Pick the file for your plywood, then cut one slot and one tab on scrap to check the kerf.
- 02Cut the 9 parts and note that the 63.6 mm cross divider goes in the narrow left column and the 106.8 mm one in the right column.
- 03Fit the two long dividers into the base, add the two cross dividers, then attach the back, the sloped sides and the low front panel.
- 04Sand, seal, and place pads in the wide center bay with tampons, liners and wipes in the four side compartments.
Wide middle, split sides
Two long dividers run the full 240 mm depth and divide the box into three columns. The center column is the widest and holds a deep stack of pads standing slightly tilted, as in the photo. Each side column has its own short cross divider: on the left, a narrow bay for tampons at the back and a bay for rounded liners in front; on the right, folded pads or liners at the back and a pack of wipes in front. The side compartments are different sizes because the cross dividers are 63.6 mm and 106.8 mm long, so the left column is clearly the narrower one.
Thickness choice
For a box this deep, 3 mm plywood is light and still rigid enough, and it cuts on a 10 W diode in about 22 min 55 s for the 3 mm file (about 9 min 33 s on a 40 W CO2, about 4 min 35 s on a 100 W CO2). 4 mm gives firmer walls if you plan to carry it between rooms. 5 and 6 mm files exist too, but a diode needs several passes on them. The 3 mm layout is 1100 × 362 mm; the 300 × 240 mm base is the largest single piece.
Make it personal
A short engraved word on the 55 mm front, a monogram, or a small flower outline turns it into a gift. Customers ask for this kind of box as a bathroom refresh for a teenage daughter, for a bridesmaid kit table, or for a guest room. Sell it oiled and empty, or stocked with supplies in a clear bag.
Questions about this file
What goes in the wide center bay?
A full stack of folded pads, standing or lying, runs the whole 240 mm depth in the middle column.
Why is the left side column narrower than the right one?
The left column is narrow, sized for tampons and small liners; the right one is wider for folded pads and a pack of wipes.
Can I make this in MDF?
MDF works with the matching thickness file, but seal it thoroughly, since its cut edges soak up moisture in a bathroom.
Can I scale it to fit a shallow cabinet?
Shorten the depth of the panels in your editor and leave every slot at the plywood thickness so the tabs still fit.
Is gluing required?
No, the tabs hold the box together. A thin line of glue on the base slots makes it permanent.
Similar files
