VisualizationOil and Sauce Organizer SVG, Two Row Bottle Holder Laser Cut File, Salt and Pepper Shaker Tray DXF, Wooden Kitchen Bin
A two-row organizer for oil bottles, sauces and spice shakers: two wide 110 mm tall bays at the back and three smaller bays in front. The download includes SVG and DXF files for 3, 4, 5 and 6 mm plywood; the outer size is 300 × 220 × 110 mm (11.81 × 8.66 × 4.33 in), it has 9 pieces and a front that slopes down to 66 mm, and it assembles with tabs and slots. Free to download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 300 × 220 × 110 mm (11.81 × 8.66 × 4.33 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,060 × 342 mm
- Cut length
- 6.73 m
- Est. time, 10 W diode (3 mm)
- 22 min 25 s
- Est. time, 40 W CO2 (3 mm)
- 9 min 21 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Measure your sheet with calipers, open the SVG or DXF for that thickness, and test one tab in one slot on scrap.
- 02Cut all 9 parts: front, back, two sides, base, the long cross divider, two short front dividers and the tall back divider.
- 03Build the outer box on the base, fit the cross divider, then add the single tall divider at the back and the two short dividers at the front.
- 04Round the edges with fine sandpaper, apply oil or lacquer, and fill the back bays with bottles and the front slots with shakers.
Two wide bays, three small ones
The back wall here is 110 mm, a little taller than most boxes in this set, which helps with tall 500 ml oil and vinegar bottles. Behind the cross divider there are only two bays, each about half the width of the box, so two or even three bottles stand side by side. In the photo the left bay holds olive oil and balsamic, the right one ketchup and a barbecue sauce.
In front, two short dividers create three equal slots that suit spice shakers: salt, mixed peppercorns and dried herbs in the picture. The front wall is 66 mm and the sides slope between the two heights.
Thickness and laser time
Pick 4 mm if you want a light box, 5 or 6 mm if the bottles are glass and the organizer will be moved often. Every thickness has its own SVG and DXF, so the tabs fit without editing. A 10 W diode cuts 3 mm in one or two passes; thicker sheets need extra passes or a CO2 laser. For the 3 mm file, expect about 22 min 25 s on a 10 W diode, about 9 min 21 s on a 40 W CO2 and about 4 min 29 s on a 100 W CO2.
The parts are laid out on a 1060 × 342 mm sheet. On a smaller bed, cut the base and back on one sheet and the sides, front and dividers on another.
Make it a set
Cut a second box from the same file and place the two side by side next to the stove, one for cooking oils and one for sauces. A matching spice tray from the same category in the same plywood keeps the counter consistent. Finish with clear oil and it can live near the hob without staining.
Questions about this file
How many bottles fit in the back row?
Each back bay is about 145 mm wide, so it holds two or three round bottles of 60 to 70 mm diameter, giving four to six bottles in total.
Why is this one 110 mm tall?
The higher back wall supports tall bottles better, so they do not lean when you pull the box toward you.
Can I make it from MDF?
Yes, MDF in 3 to 6 mm cuts cleanly with the matching file, but it swells if it gets wet, so seal it well for kitchen use.
Should I glue it?
Glue is optional; the tabs hold firmly. Add wood glue to the base joints if the box will carry several glass bottles every day.
Can I engrave a name on the front?
The file is cut lines only, but you can add a name or a word like Oils in your laser software as an engrave layer on the 300 mm front.
Similar files
