VisualizationSkincare Vanity Tray SVG, Six Cell Cosmetic Organizer Laser Cut File, Wooden Cream Jar Holder DXF
A six-cell skincare vanity tray arranged as two rows of three, offered as SVG and DXF with a separate file set for 3, 4, 5 and 6 mm plywood. It is 320 × 210 × 110 mm (12.6 × 8.27 × 4.33 in), uses 10 pieces, and has a sloped front 55 mm high. It goes together with tabs and slots and is free to download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 320 × 210 × 110 mm (12.60 × 8.27 × 4.33 in)
- Parts
- 10
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,088 × 332 mm
- Cut length
- 7.16 m
- Est. time, 10 W diode (3 mm)
- 23 min 51 s
- Est. time, 40 W CO2 (3 mm)
- 9 min 56 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Select the file for your plywood thickness and check the fit with one test slot on an offcut.
- 02Cut the 10 parts: front, back, two sloped sides, base, the cross divider and four short dividers.
- 03Put the two tall back dividers and two low front dividers into the base, slide the cross divider across them, then add the back, the sides and the front.
- 04Sand the edges, apply oil or clear lacquer, and give each of the six cells one product.
Three over three
This tray is laid out as two even rows. A long cross divider separates the tall back row from the lower front row, and two dividers on each side of it make three cells per row, six in all. The back wall is 110 mm, one of the taller versions in this set, which helps keep sheet masks and taller dropper bottles from tipping.
In the photo the back row holds sheet masks, a frosted and an amber serum, and a tower of cotton pads. The front row has three cream jars, one per cell, including one with a rose-gold lid. It is a good layout for anyone who keeps separate day cream, night cream and eye cream.
Choosing the thickness
You get SVG and DXF for 3, 4, 5 and 6 mm sheets. The cells are already fairly small, so 3 or 4 mm plywood leaves the most room inside; 6 mm makes a heavier tray that feels solid but narrows every cell. Test one slot whatever you choose, because plywood labelled 3 mm is often 2.8 or 3.2 mm.
The 3 mm sheet layout is 1088 × 332 mm. On a 400 mm bed, put the base and back on one sheet and the rest on a second. For the 3 mm file the job takes about 23 min 51 s on a 10 W diode, about 9 min 56 s on a 40 W CO2 and about 4 min 46 s on a 100 W CO2.
Gift and selling ideas
Fill the six cells with a small skincare set and wrap it as a birthday gift. On Etsy, photograph it filled from above so buyers can count the cells, and offer it plain or with a stained finish.
Questions about this file
How big is each cell?
The tray is divided into two rows of three across a 320 mm length, so each cell is roughly a third of the width, enough for a standard 50 ml cream jar.
Can I resize it for a wider vanity?
Scaling works for the outline, but every slot must stay as wide as the sheet you cut, so fix the slot widths after resizing.
Does it work in clear acrylic?
Yes, pick the file for the acrylic thickness and test a slot first. Clear acrylic shows every product label from the front.
How do I make the joints permanent?
Run a thin line of wood glue into each slot before pressing the tabs in, then wipe off any squeeze-out with a damp cloth.
Can I personalise it with a name?
Yes, add a name or initials to the front panel in your laser software before cutting; the file itself contains only cut lines.
Similar files
