VisualizationSanitary Pad Organizer SVG, Tampon and Liner Holder Laser Cut File, Bathroom Period Box DXF
A sloped-front bathroom organizer for sanitary pads, panty liners, tampons and wipes, supplied as SVG and DXF with separate files for 3, 4, 5 and 6 mm plywood. The outer size is 340 × 160 × 120 mm (13.39 × 6.30 × 4.72 in); 8 tab-and-slot pieces make four compartments, with the right-hand bay split by a short cross divider. The whole set of files is a free download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 340 × 160 × 120 mm (13.39 × 6.30 × 4.72 in)
- Parts
- 8
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,364 × 292 mm
- Cut length
- 5.84 m
- Est. time, 10 W diode (3 mm)
- 19 min 28 s
- Est. time, 40 W CO2 (3 mm)
- 8 min 07 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Pick the SVG or DXF that matches your plywood (3, 4, 5 or 6 mm) and cut a single slot with a scrap tab to check the fit before the full run.
- 02Cut the 8 parts, splitting the 1364 mm layout across smaller sheets if your bed is short, and keep the small cross divider aside so it does not get lost.
- 03Push the two long dividers into the base, fit the back and both sloped sides, close it with the low front, then slide the cross divider into the right bay.
- 04Sand, seal with lacquer or oil, and load pads on the left, liners in the middle, tampons and wipes in the split right bay.
What fits inside
The widest bay on the left takes a full stack of folded maxi or night pads lying on their backs, the way they come out of the pack. The middle bay is narrower and suits panty liners or ultra-thin pads in round wrappers. On the right, a short cross divider splits the last bay in two: tampons stand upright behind it, and a flat pack of intimate wipes lies in front where you can pull a sheet without lifting anything. The front wall is 60 mm against a 120 mm back, so every row stays visible from above when the box sits on a bathroom counter or inside a vanity cabinet.
Cutting and assembly
There are 8 parts: front, back, two sloped sides, base, two long dividers and the small cross divider. For the 3 mm file the cut takes about 19 min 28 s on a 10 W diode, about 8 min 07 s on a 40 W CO2 and about 3 min 54 s on a 100 W CO2. A diode handles 3 mm in one or two passes; 5 and 6 mm sheets want a CO2 or several slow passes. The 3 mm layout runs 1364 × 292 mm, longer than most hobby beds, so split the pieces across two or three sheets. Seat the long dividers into the base first, then add the back, sides and front, and drop the cross divider in last. Joints hold without glue, but a drop of wood glue makes the box permanent.
Finishing and selling
Sand the edges lightly and wipe on a clear lacquer or hardwood oil, since splashes near a sink will raise the grain of bare birch. For Etsy, offer it stocked as a ready "period kit", as a guest bathroom basket for hosts and Airbnb owners, or in a matching pair with a cotton pad box.
Questions about this file
Will a whole pack of maxi pads fit in the left bay?
The left bay is the widest of the three and runs the full 160 mm depth, so a typical folded pad stack fits lying flat. Very long overnight pads may sit at a slight angle.
Can I scale this organizer up for bigger packs?
Yes, but the slot widths must stay equal to the plywood thickness or the tabs will be loose or will not go in. Stretch the panels in your editor and leave the slots at 3, 4, 5 or 6 mm.
Which plywood thickness should I use for a box that gets moved daily?
3 mm keeps it light and quick on a diode; 4 or 5 mm feels sturdier if it is pulled out of a cabinet every morning.
Is bare plywood safe next to the sink?
Bare birch swells with water, so seal every face with clear lacquer, polyurethane or hardwood oil and wipe splashes off when they happen.
Can I put a word like "supplies" on the low front?
The file has cut lines only, but the 60 mm front panel takes a short engraved word or a small icon if you add an engrave layer in your laser software.
Similar files
