VisualizationLong Pad Organizer SVG, Bathroom Counter Tampon and Wipes Tray, Feminine Hygiene Storage Laser DXF
A long, shallow bathroom counter organizer with six bays: a pad bay on the left, two center columns each split into a tampon bay and a liner bay, and a wipes bay on the right. Files come as SVG and DXF for 3, 4, 5 and 6 mm plywood; the box is 440 × 160 × 110 mm (17.32 × 6.30 × 4.33 in) with 10 tab-and-slot parts and a sloped front. There is no charge to download them.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 440 × 160 × 110 mm (17.32 × 6.30 × 4.33 in)
- Parts
- 10
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,664 × 282 mm
- Cut length
- 7.47 m
- Est. time, 10 W diode (3 mm)
- 24 min 53 s
- Est. time, 40 W CO2 (3 mm)
- 10 min 22 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Confirm your bed takes a 440 mm part, choose the file for your plywood, and cut one test slot.
- 02Cut the 10 parts and mark the 91 mm and 88 mm cross dividers so each goes into its own middle column.
- 03Fit the three long dividers into the base, add the two cross dividers to the middle columns, then close the box with back, sloped sides and front.
- 04Sand, oil or lacquer, and load pads on the left, tampons and liners in the middle and wipes on the right.
The longest box in the set
At 440 mm long and only 160 mm deep, this organizer runs along the back of a vanity or the side of a sink without taking much counter depth. Three full-depth dividers make four columns. The left one holds a tall stack of pads; the right one holds a large pack of wipes lying flat. The two middle columns each have a short cross divider (91 mm and 88 mm, 79.3 mm high), so tampons lie in a row at the back and liners in the bay in front. Sloping from 110 mm to 55 mm, the sides keep the whole length visible.
Fitting a 1664 mm layout
The 3 mm layout is 1664 × 282 mm. Front, back and base are each 440 mm long, so your bed has to take 440 mm in one direction; everything else can move to other sheets. The 3 mm file cuts in about 24 min 53 s on a 10 W diode, about 10 min 22 s on a 40 W CO2 and about 4 min 59 s on a 100 W CO2. A diode gets through 3 mm in one or two passes, while the 5 and 6 mm files are better on a CO2. Keep the two cross dividers apart after cutting, as they differ by 3 mm.
Finishing and gifts
A long box shows off the wood, so a clear oil that keeps the light birch colour works well; seal the base underside too, since counters get wet. Sell it for bathrooms with a long, narrow counter, as a shared supply tray for dorm bathrooms, or engraved with a family name on the front as a housewarming gift.
Questions about this file
How much counter space does it need?
A strip 440 mm long and 160 mm deep (17.32 × 6.30 in), which suits the back edge of most vanities.
Are the two middle columns the same?
Almost: their cross dividers are 91 mm and 88 mm long, so mark them after cutting to avoid swapping them.
Can I shorten it for a smaller counter?
Yes, shorten the long panels in your editor and keep each slot equal to the plywood thickness so the joints still fit.
Is MDF a good alternative?
MDF cuts well and paints nicely, but next to a sink it must be sealed on every edge to avoid swelling.
Can I put a family name on it?
Yes, the front panel is long enough for an engraved name. Add it as an engrave layer; the file only contains cut lines.
Similar files
