VisualizationJewelry Tray SVG, Sloped Vanity Organizer Laser Cut File, Three Section Accessory Box DXF
A sloped-front jewelry tray with three sections: one wide bay for sunglasses and bracelets and two narrower slots for a watch, rings and earrings. The free download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; the box measures 360 × 170 × 80 mm (14.17 × 6.69 × 3.15 in), is cut from 7 pieces and assembles with tabs and slots.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 360 × 170 × 80 mm (14.17 × 6.69 × 3.15 in)
- Parts
- 7
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,444 × 262 mm
- Cut length
- 5.22 m
- Est. time, 10 W diode (3 mm)
- 17 min 24 s
- Est. time, 40 W CO2 (3 mm)
- 7 min 15 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Pick the SVG or DXF for your plywood (3, 4, 5 or 6 mm) and cut a single divider slot in scrap to check that the tab slides in snugly.
- 02Cut the seven parts; on a small bed split the 1444 mm layout so the base and back go on a second sheet.
- 03Set both dividers into the base, add the 80 mm back wall, slide on the two sloped sides and finish with the 48 mm front.
- 04Sand the edges, wipe on clear lacquer or oil, then lay sunglasses in the wide bay and a watch and earrings in the two slots.
What fits inside
Two front-to-back dividers split this tray into three bays. The left bay is the big one: a pair of sunglasses lies flat in it with a stack of bangles or a beaded bracelet in front. The middle slot is narrow and suits a watch on its strap plus two or three rings. The right slot takes an earring card or a small velvet stand with pearl drops and studs.
The back wall is 80 mm tall and the front only 48 mm, so the side panels slope down toward you. Standing at the dresser you can see every piece without lifting anything out.
Cutting and assembly
Seven parts make up the box: front, back, two sloped sides, base and two dividers. Estimated cutting time for the 3 mm file is about 17 min 24 s on a 10 W diode, about 7 min 15 s on a 40 W CO2 and about 3 min 29 s on a 100 W CO2. A 10 W diode gets through 3 mm plywood in one or two passes; for the 5 and 6 mm files expect several slow passes or use a CO2 tube.
The nested layout is 1444 × 262 mm, longer than most hobby beds, so move the base and back onto a second sheet (or a third) before cutting. Push both dividers into the base, add the back, slide on the sides and close with the low front. The tabs hold on their own; a drop of wood glue in each slot makes the tray permanent.
Gift and shop ideas
- A bridesmaid gift, filled with the earrings and bracelet she will wear on the day.
- A dresser catchall offered in natural birch and in a walnut stain.
- Bundle it with a ring cone and sell the two as a vanity set.
Questions about this file
Do sunglasses really fit in the big section?
Yes. The left bay is the widest of the three and the tray is 170 mm deep, so most folded sunglasses lie flat with room for bangles in front of them.
Can I shrink the tray for a narrow dresser top?
You can scale the drawing, but every slot must stay as wide as your plywood is thick, so fix the slots after scaling or the tabs will not fit. Cutting it at full size is the simplest option.
Which plywood thickness suits a jewelry tray best?
3 or 4 mm birch keeps the tray light and neat. 5 or 6 mm looks chunkier and is sturdier, but takes much longer on a diode laser.
Can I cut it from MDF instead of birch?
Yes, use the file that matches the MDF thickness. Paint or seal it afterwards, because raw MDF marks easily from metal clasps.
Can I engrave a monogram on the low front?
The file has cut lines only, but the 360 × 48 mm front has room for initials. Add a text layer in your laser software and engrave it before the cut.
Similar files
