VisualizationJewelry Box SVG, Nine Compartment Grid Organizer DXF, Earring Ring and Bracelet Storage Box Laser Cut File
A nine-compartment jewelry box laid out as a 3 × 3 grid with straight 80 mm walls, for sorting earrings, rings, bracelets, a watch and sunglasses one type per square. It measures 350 × 280 × 80 mm (13.78 × 11.02 × 3.15 in), uses 13 pieces joined with tabs and slots, and the free download includes SVG and DXF files for 3, 4, 5 and 6 mm plywood.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 350 × 280 × 80 mm (13.78 × 11.02 × 3.15 in)
- Parts
- 13
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,410 × 456 mm
- Cut length
- 9.59 m
- Est. time, 10 W diode (3 mm)
- 31 min 57 s
- Est. time, 40 W CO2 (3 mm)
- 13 min 19 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the SVG or DXF for your plywood and cut one cross-divider slot on scrap to check the fit.
- 02Cut the thirteen parts, putting the 350 × 280 mm base on a sheet of its own.
- 03Slide three cross dividers onto each long divider, place the grid on the base and add the four 80 mm walls.
- 04Sand the grid tops, finish with lacquer or oil and give each of the nine squares one type of jewelry.
Nine squares for a growing collection
This is the largest and most divided box in the jewelry set. Two long dividers run the full 280 mm depth and six short cross dividers split each of the three columns into three, giving a 3 × 3 grid of nine compartments, each roughly 110 × 90 mm. All walls and dividers are 80 mm tall, so nothing slides over into the next square.
In the photo the top row holds knot earrings, pearl drops and sunglasses; the middle row stacked rings, a watch and a pearl bracelet; the bottom row gold hoops, a clover bracelet and a rose quartz bracelet. Nine squares give room for a collection to grow without reorganizing.
Cutting thirteen parts
The part count is the highest here: front, back, two sides, base, two long dividers and six cross dividers. For the 3 mm file allow about 31 min 57 s on a 10 W diode, about 13 min 19 s on a 40 W CO2 or about 6 min 23 s on a 100 W CO2. The 3 mm layout is 1410.4 × 456 mm, wider than the other layouts because of the 350 × 280 mm base. Cut the base on its own sheet and spread the walls and the eight dividers over two or three more.
On a 10 W diode, the 3 mm file is comfortable; the 6 mm box is very strong but slow to cut, and a CO2 laser handles it far better.
Assembly and uses
Fit three cross dividers onto each long divider, lay the grid on the base and close it with the four walls. With this many joints glue is not needed. Finish with lacquer or oil, and add felt squares if you like. Beyond jewelry, the grid suits hair clips, nail polish or watch straps, and it sells well at craft fairs as a jewelry box for a teenager's room.
Questions about this file
How big is each square in the grid?
With a 350 × 280 mm outside and three columns by three rows, each compartment is roughly 110 × 90 mm and 80 mm deep.
Can I use it for things other than jewelry?
Yes. The nine squares suit hair clips, nail polish, watch straps or craft supplies just as well.
My bed is 400 × 400 mm. Will the base fit?
Yes, the 350 × 280 mm base fits in one piece. Cut the walls and dividers on separate sheets.
Why must slots match the plywood thickness?
Each tab is cut to slide into a slot of exactly that width. If you scale the file or use thinner stock, the joints become loose or will not go together.
Can I seal it for use in a bathroom?
Yes. Apply two coats of polyurethane or hard-wax oil to every surface, including the dividers, and let it cure before use.
Similar files
