VisualizationJewelry Box SVG, Three Column Earring and Ring Organizer DXF, Straight Wall Dressing Table Tray Laser Cut File
A straight-walled jewelry box in three columns: an earring bay on the left, a wide center bay for sunglasses and a watch, and a right column split into three stacked slots for rings and bracelets, five compartments in total. It measures 420 × 190 × 70 mm (16.54 × 7.48 × 2.76 in), consists of 9 tab-and-slot pieces, and the free download includes SVG and DXF for 3, 4, 5 and 6 mm plywood.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 420 × 190 × 70 mm (16.54 × 7.48 × 2.76 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,664 × 272 mm
- Cut length
- 6.86 m
- Est. time, 10 W diode (3 mm)
- 22 min 51 s
- Est. time, 40 W CO2 (3 mm)
- 9 min 31 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Download the version for your sheet thickness and test-cut one cross-divider slot on scrap.
- 02Cut the nine pieces on a bed long enough for the 420 mm front, back and base.
- 03Attach both cross dividers to the right-hand long divider, stand both long dividers in the base and add the four straight walls.
- 04Sand, lacquer or oil, line the center bay with velvet and fill the three stacked slots with rings and bracelets.
Three columns
Two long dividers run the full 190 mm depth and make three columns. The left column is open and holds an earring cushion with pearl drops and a pair of hoops. The center column is the widest and takes sunglasses with a mesh watch below them. Two short cross dividers (108 mm each) cut the right column into three slots stacked from back to front, used in the photo for rings, a pearl bracelet and a gold cuff.
All walls are 70 mm, with no slope, so the box sits cleanly on a dressing-table island or slides into a wide drawer. At 420 mm it is one of the longer boxes in the set, giving each column real room.
Cutting and putting it together
Nine pieces: front, back, two sides, base, two long dividers and two cross dividers. Cut times for the 3 mm file are about 22 min 51 s on a 10 W diode, about 9 min 31 s on a 40 W CO2 and about 4 min 34 s on a 100 W CO2. The full layout is 1664 × 272 mm, and the front, back and base are 420 mm long, so your bed must handle that length; the dividers and sides fit on scraps.
Hook the two cross dividers onto the right-hand long divider, place both long dividers in the base, then add the walls. It holds firmly without glue; one drop per joint makes it permanent. On a diode, stay with 3 or 4 mm unless you are willing to run several passes for the thicker files.
Finishing ideas
Sand all edges, then use clear lacquer for a pale look or oil for warmth. Line the center bay with velvet to protect sunglasses lenses. As a gift it suits someone with a walk-in closet or dressing table; sellers can offer it in natural and dark-stained versions.
Questions about this file
What goes in the three stacked slots?
They are narrow strips across the right column, ideal for rings, a bracelet and a cuff, one type per slot.
Can it go inside a dresser drawer?
If the drawer is at least 420 × 190 mm inside and over 70 mm tall, yes; the straight walls make it drawer-friendly.
Which thickness should I use on a CO2 laser?
Any of the four. 4 mm is a good middle ground: sturdy, but still light and quick to cut.
Can I glue in a velvet lining?
Yes. Cut fabric or self-adhesive velvet to each bay and press it onto the base after finishing the wood.
Can I add a name to the front panel?
The file is cut-only, but the 420 mm front is a good place for an engraved name you add in your laser software.
Similar files
