VisualizationLong Accessory Tray SVG, Six Section Jewelry Organizer DXF, Bathroom Counter Earring and Watch Tray Laser Cut File
A long accessory tray with straight walls and six sections: an end bay for sunglasses, a 2 × 2 block of small cubbies in the middle for earrings and rings, and an end bay for a watch and bracelets. It measures 460 × 170 × 70 mm (18.11 × 6.69 × 2.76 in), uses 10 tab-and-slot pieces and comes as a free SVG and DXF download for 3, 4, 5 and 6 mm plywood.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 460 × 170 × 70 mm (18.11 × 6.69 × 2.76 in)
- Parts
- 10
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,744 × 252 mm
- Cut length
- 7.30 m
- Est. time, 10 W diode (3 mm)
- 24 min 19 s
- Est. time, 40 W CO2 (3 mm)
- 10 min 08 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Make sure your bed takes the 460 mm parts, choose the file for your plywood and test-cut one slot.
- 02Cut the ten parts, spreading the 1744 mm layout over several sheets with the long pieces kept whole.
- 03Build the four-cubby block from the cross divider and two small dividers, fit it between the long dividers on the base, then add the four 70 mm walls.
- 04Seal with polyurethane for bathroom use and fill the end bays with sunglasses and a watch and the cubbies with small jewelry.
Two end bays and a block of four
At 460 mm this is the longest tray in the jewelry set, but only 170 mm deep, so it lines up neatly along a bathroom counter or the back of a dresser. Two long dividers mark off a bay at each end. The middle section is split by a short cross divider and two small dividers into four cubbies, two at the back and two at the front.
In the photo the left bay holds tortoiseshell sunglasses, the four cubbies take pearl drops, rings, crystal studs and a fine bracelet, and the right bay a watch with a rose quartz bracelet and a bangle. All walls are 70 mm with no slope.
Cutting a long tray
Ten parts: front, back, two sides, base, two long dividers, one cross divider and two small dividers. As a guide for the 3 mm file, it takes about 24 min 19 s on a 10 W diode, about 10 min 08 s on a 40 W CO2 and about 4 min 52 s on a 100 W CO2. The layout is 1744 × 252 mm, the longest in the set. The front, back and base are 460 mm, so a 400 mm bed is too short for them at this size; check your machine before buying plywood.
On a diode, 3 mm cuts in one or two passes. For 5 or 6 mm, slow down and add passes, or use a CO2 laser.
Assembly and bathroom finish
Fit the two small dividers to the cross divider, slot that block between the long dividers, set everything on the base and add the walls. Glue is optional. For a sink-side spot like the one in the photo, seal every face, including under the base, with two coats of polyurethane. Paired with a soap dish or a toothbrush holder it makes a matching bathroom set, and it works as a housewarming gift.
Questions about this file
What fits in the four middle cubbies?
They are small and suit earrings, rings, studs or a fine chain bracelet, one item type per cubby.
Can I cut it on a 400 mm laser bed?
Not at full size, because the front, back and base are 460 mm long. You can scale it down, but then set every slot back to your real material thickness.
Will it hold up next to a bathroom sink?
Yes, once all faces are sealed with polyurethane or hard-wax oil. Do not let water pool inside the cubbies.
Would acrylic work for this tray?
Yes, pick the version closest to your acrylic sheet. Acrylic is waterproof and suits a bathroom, but the joints need acrylic cement.
Should I glue it?
It stays together without glue. Since this tray is long, a little wood glue in the base slots keeps it from flexing when lifted at one end.
Similar files
