VisualizationSkincare Organizer SVG, Slanted Three Section Vanity Box Laser Cut File, Wooden Serum Holder DXF
A slanted three-section skincare organizer for a vanity or dresser, supplied as SVG and DXF with separate files for 3, 4, 5 and 6 mm plywood. It measures 300 × 170 × 110 mm (11.81 × 6.69 × 4.33 in), is cut from 7 pieces, and its two long dividers create three sections behind a 55 mm sloped front. The box assembles with tabs and slots, and the file set is a free download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 300 × 170 × 110 mm (11.81 × 6.69 × 4.33 in)
- Parts
- 7
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 960 × 292 mm
- Cut length
- 5.11 m
- Est. time, 10 W diode (3 mm)
- 17 min 01 s
- Est. time, 40 W CO2 (3 mm)
- 7 min 05 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Pick the SVG or DXF that matches your plywood (3, 4, 5 or 6 mm) and cut one divider slot as a test to see that a scrap of the same sheet slides in snugly.
- 02Cut all 7 parts: front, back, two sloped sides, base and the two long dividers.
- 03Seat both dividers in the base, fit the 110 mm back, then the two sides, and close the box with the 55 mm front.
- 04Sand the edges, wipe on clear oil or lacquer, and load masks, serums and cotton pads into the three sections.
What fits inside
This is the simplest layout in the skincare set: two full-height dividers run from front to back and split the box into three tall sections. In the photo the left section holds sheet masks standing upright with two cream jars in front of them, the middle one keeps two serum dropper bottles, and the right one takes a stack of cotton pads. The back wall is 110 mm tall and the front drops to 55 mm, so the side panels slope and every label stays visible from your chair.
At 300 × 170 mm the base fits on most dressing tables without crowding a mirror or a lamp.
Cutting and assembly
The download has eight files: an SVG and a DXF for each plywood thickness from 3 to 6 mm, with slots matched to that sheet. The 3 mm layout is 960 × 292 mm, so on a smaller bed you can move the base and the back onto a second sheet. Cutting time for the 3 mm file is about 17 min 01 s on a 10 W diode, about 7 min 05 s on a 40 W CO2 and about 3 min 24 s on a 100 W CO2. A diode handles 3 mm in one or two passes; 5 or 6 mm needs more power or several passes.
Press the two dividers into the base first, then add the back, both sloped sides and the low front. Tab-and-slot joints hold without glue, but a drop of wood glue in each slot makes the box permanent.
Ideas for selling
Three sections is an easy layout to explain in a listing photo: masks, serums, pads. Sell it in birch with a clear oil finish, offer a white-painted version for bright bathrooms, or bundle it with a jar of homemade body butter as a gift.
Questions about this file
What can I keep in the three sections?
In the photo the sections hold sheet masks with cream jars, two dropper serums, and a stack of cotton pads. Any bottle under about 150 mm tall stands upright comfortably.
Can I make the box longer to add a fourth section?
You can scale the outline in your software, but slot widths must stay equal to your plywood thickness, so resize the slots back after scaling. Adding a section means drawing one more divider and its base slots.
Will 3 mm MDF work instead of plywood?
Yes, use the 3 mm file and cut a test slot first because MDF is often slightly thicker than its label. MDF swells with water, so seal it well if the box goes near a sink.
Is glue required?
No. The tabs and slots hold the box together on their own; glue only makes it permanent.
How do I keep serum oils from staining the wood?
Oils darken bare birch, so brush on a clear water-based lacquer before use. After that, a damp cloth removes most spills.
Similar files
