VisualizationLong Skincare Vanity Organizer SVG, Six Bay Dressing Table Tray Laser Cut File, Wooden Serum Display DXF
An extra-long skincare vanity organizer with two full-depth end bays and a four-cell block in the middle, available as SVG and DXF in separate versions for 3, 4, 5 and 6 mm plywood. It measures 400 × 170 × 100 mm (15.75 × 6.69 × 3.94 in), is cut from 9 pieces, and has six compartments behind a 55 mm sloped front. It assembles with tabs and slots and can be downloaded free.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 400 × 170 × 100 mm (15.75 × 6.69 × 3.94 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,564 × 282 mm
- Cut length
- 6.79 m
- Est. time, 10 W diode (3 mm)
- 22 min 38 s
- Est. time, 40 W CO2 (3 mm)
- 9 min 26 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the file for your plywood thickness, check that your bed takes the 400 mm parts, and test one slot.
- 02Cut the 9 parts: front, back, two sloped sides, the 400 mm base, two long dividers, the short cross divider and the small middle divider.
- 03Fit the long dividers into the base, slot the cross divider between them, add the small divider, then the back, sides and front.
- 04Sand and finish, then put masks and pads in the end bays and serums and jars in the four middle cells.
The longest box in the set
At 400 mm this organizer runs the full width of a typical dressing table while staying only 170 mm deep. Two long dividers mark off a full-depth bay at each end. Between them, a short cross divider and one small divider make a block of four cells, two at the back and two at the front, for six compartments in total.
The photo, taken in a walk-in dressing room with clothes on rails behind, shows the layout at work. The left end bay holds a fan of sheet masks, the two middle back cells a clear and an amber serum, the two middle front cells a white and a pink jar, and the right end bay a tall stack of cotton pads with a rose-gold jar in front.
Cutting a 400 mm box
The front, back and base are each 400 mm long, so your laser bed must take that length. The 3 mm layout is 1564 × 282 mm, the longest in this category; split it into two or three sheets with the long parts on their own. For the 3 mm file expect about 22 min 38 s on a 10 W diode, about 9 min 26 s on a 40 W CO2 and about 4 min 32 s on a 100 W CO2. With 5 or 6 mm stock, plan on multiple diode passes.
Assembly and finish
Set the two long dividers into the base, fit the cross divider between them, then the small middle divider. Add the back, both sloped sides and the front. With a long base, a drop of wood glue in the divider slots helps keep it flat. Finish with clear oil, or lacquer if the table sees cream spills.
In a shop listing, show it next to a mirror so buyers see the length; it also works as a dressing room display shelf.
Questions about this file
What laser bed size do I need?
The longest parts are 400 mm, so the bed must fit that length; all other pieces are shorter and can be cut on extra sheets.
What goes in the end bays?
They run the full 170 mm depth, so tall items such as sheet masks, a cotton pad stack or a toner bottle fit best there.
Can I shorten it for a smaller table?
Shorten the front, back, base and cross divider in your software and keep every slot equal to your sheet thickness.
Which plywood thickness is best for a long box?
4 or 5 mm keeps the 400 mm walls straight; with 3 mm, glue the divider slots for extra stiffness.
Can I add initials to it?
Yes, engrave initials or a name on the long front panel by adding them in your laser software; the file has cut lines only.
Similar files
