VisualizationLow Front Skincare Organizer SVG, Five Section Dresser Tray Laser Cut File, Cream and Mask Holder DXF
A low-front skincare organizer with two wide full-depth bays and a column of three stepped cells, provided as SVG and DXF with separate files for 3, 4, 5 and 6 mm plywood. It measures 360 × 190 × 100 mm (14.17 × 7.48 × 3.94 in), is cut from 9 pieces, and has five compartments behind a front wall only 50 mm high. It is assembled with tabs and slots, and the files are free to download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 360 × 190 × 100 mm (14.17 × 7.48 × 3.94 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,120 × 302 mm
- Cut length
- 6.54 m
- Est. time, 10 W diode (3 mm)
- 21 min 49 s
- Est. time, 40 W CO2 (3 mm)
- 9 min 05 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the file for your plywood thickness and do a test cut of one slot to check the fit.
- 02Cut the 9 parts: the 50 mm front, back, two sloped sides, base, two long dividers and two short cross dividers.
- 03Set both long dividers in the base, add the two short cross dividers to the right column, then fit the back, the sides and the front.
- 04Sand the edges, oil or lacquer the box, and fill the wide bays with jars and masks and the small cells with serums, pads and a pot.
The lowest front in the set
Most boxes in this group have a 55 or 60 mm front; this one drops to 50 mm, so the slope from the 100 mm back is the steepest and products sit almost fully on show. Two long dividers create two wide bays on the left and in the middle, each running the full 190 mm depth. The right-hand column is split by two short cross dividers into three small cells that step down toward the front, five compartments in all.
On the white dresser in the photo, the left bay holds a large and a small cream jar, the middle bay a stack of sheet masks with a cherry-blossom print, and the side column a clear and an amber serum at the back, cotton pads in the middle cell and a small jar at the front.
Fitting it on your bed
Each thickness from 3 to 6 mm has its own SVG and DXF with slots to match. The 3 mm layout is 1120 × 302 mm; on a smaller bed, the 360 mm base, front and back fit on one sheet and the sides and dividers on another. Cutting the 3 mm file takes about 21 min 49 s on a 10 W diode, about 9 min 05 s on a 40 W CO2 and about 4 min 22 s on a 100 W CO2. Thick 5 or 6 mm sheets mean extra passes on a diode.
Building and finishing
Start with the two long dividers in the base, then slide the two short cross dividers into the right column. Add the back, the sloped sides and the low front. The tabs hold without glue; use a drop of wood glue if the box will travel.
A low front shows off products, so it works as a retail display for handmade creams. As a gift, put a jar in the left bay and a week of masks in the middle.
Questions about this file
Why is the front only 50 mm high?
A lower front makes the slope steeper, so labels and lids are visible and easy to reach from a seated position.
Will small jars tip out over the low front?
No, 50 mm is still taller than most cream jars sit, and the side column keeps the smallest items in their own cells.
Can I cut it from acrylic for a shop counter?
Yes, choose the file for your acrylic thickness and test one slot; clear or frosted acrylic suits a retail display.
Which thickness works best for this box?
3 or 4 mm plywood keeps the wide bays roomy and cuts quickly; 5 or 6 mm gives a heavier display box but needs a stronger laser or extra passes.
How do I make it last near a sink?
Seal all faces and edges with water-based polyurethane or hardwax oil, and keep it off standing water.
Similar files
