VisualizationSkincare Bottle Organizer SVG, Six Slot Vanity Rack Laser Cut File, Wooden Divided Cosmetic Box DXF
A six-slot skincare bottle organizer with five full-height dividers in a single row, delivered as SVG and DXF with separate files for 3, 4, 5 and 6 mm plywood. It measures 320 × 170 × 110 mm (12.6 × 6.69 × 4.33 in), is cut from 10 pieces, and its sides slope from a 110 mm back to a 55 mm front. It locks together with tabs and slots and is free to download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 320 × 170 × 110 mm (12.60 × 6.69 × 4.33 in)
- Parts
- 10
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,198 × 292 mm
- Cut length
- 7.35 m
- Est. time, 10 W diode (3 mm)
- 24 min 29 s
- Est. time, 40 W CO2 (3 mm)
- 10 min 12 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Pick the file for your plywood thickness and test one divider slot on scrap before cutting all ten parts.
- 02Cut the 10 parts: front, back, two sloped sides, base and five dividers.
- 03Press all five dividers into the base, fit the back to square them up, then add the sides and the 55 mm front.
- 04Sand and finish, then fill the six slots in the order you use the products.
Six narrow slots in a row
Five dividers, all full height and full depth, split this box into six narrow slots across its 320 mm length. Narrow slots work like a rack: bottles lean on the dividers instead of on each other, and you lift one out without tipping the rest. With a 110 mm back wall, tall droppers stay upright.
The photo shows it on a bedroom dressing table with a candle and a vase of dried flowers. From left: two cream jars stacked front to back, a gold-capped serum with an amber dropper, a slim stack of sheet masks, cotton pads, a gold-lidded jar, and two more small jars. One product type per slot makes a good order for a step-by-step routine.
Fitting it on your laser
The 3 mm sheet layout is 1198 × 292 mm. Five dividers are the same size, so they nest well on a second small sheet if your bed is shorter than that. For the 3 mm file the job takes about 24 min 29 s on a 10 W diode, about 10 min 12 s on a 40 W CO2 and about 4 min 54 s on a 100 W CO2. Plywood of 5 or 6 mm is a CO2 job, or several passes on a diode, and thick dividers also make each slot noticeably narrower.
Assembly
Press all five dividers into the base, then add the back so they stand square, followed by the two sides and the front. Glue is optional, though a drop per slot makes the row of dividers rigid.
Selling idea: label each slot with a step number engraved on the front panel, cleanse to moisturize, and sell it as a routine organizer.
Questions about this file
How wide is each slot?
Five dividers split the 320 mm length into six slots of roughly equal width, enough for one dropper bottle or a small jar.
Which thickness keeps the slots widest?
3 mm plywood takes the least space; with 6 mm the five dividers use up about 15 mm more of the inside length.
Can I engrave step numbers on it?
Yes, add numbers or words above each slot on the front panel in your laser software; the file only contains cut lines.
Can I scale it for bigger bottles?
Scaling works if you correct the slot widths back to your sheet thickness afterwards.
Can it stand next to the bathroom sink?
Yes, once every face and edge is sealed with water-based polyurethane or hardwax oil; bare plywood marks from water and cream.
Similar files
