VisualizationSkincare Holder SVG, Four Bay Bathroom Counter Organizer Laser Cut File, Slanted Wooden Toiletry Box DXF
A four-bay slanted skincare holder for a bathroom counter, provided as SVG and DXF with separate files for 3, 4, 5 and 6 mm plywood. It measures 340 × 190 × 110 mm (13.39 × 7.48 × 4.33 in), is made from 8 pieces, and three full-height dividers create four side-by-side bays behind a 61 mm sloped front. It holds together with tabs and slots and is a free download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 340 × 190 × 110 mm (13.39 × 7.48 × 4.33 in)
- Parts
- 8
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,080 × 312 mm
- Cut length
- 6.32 m
- Est. time, 10 W diode (3 mm)
- 21 min 04 s
- Est. time, 40 W CO2 (3 mm)
- 8 min 47 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the file for your plywood thickness and confirm the slot width with one test cut in scrap.
- 02Cut the 8 parts: front, back, two sloped sides, base and three full-height dividers.
- 03Insert the three dividers into the base, add the back and both sides, and close it with the 61 mm front.
- 04Sand, seal against water, let it cure, and fill one bay each with serums, jars, masks and cotton pads.
Four bays across
Three dividers run straight from the back wall to the front, splitting this holder into four bays of similar width, each the full 190 mm deep. There are no cross dividers, so every bay is long enough for a tall bottle at the back and a jar in front.
The photo shows it on a wooden bathroom counter next to a white basin. Left to right: two gold-capped serums, a pair of cream jars, a stack of sheet masks, and cotton pads. The 110 mm back and 61 mm front give a steep slope, so the masks lean back and stay readable.
Cutting and assembly
You get an SVG and a DXF for each sheet thickness from 3 to 6 mm, with matching slot widths. The 3 mm layout is 1080 × 312 mm. If your bed is 400 mm or smaller, nest the 340 mm long parts on one sheet and the sides and dividers on another. The 3 mm file runs about 21 min 04 s on a 10 W diode, about 8 min 47 s on a 40 W CO2 and about 4 min 13 s on a 100 W CO2.
Slide the three dividers into the base, then fit the back and both sides; the front goes on last. Glue is optional.
Finishing for the bathroom
Because it lives by the sink, seal it well: sand the edges, then apply a water-based polyurethane or hardwax oil to all faces, base underside included. Let it cure for a day before putting bottles in.
To sell, list it as a bathroom counter organizer and show it holding a mix of skincare and toiletries such as toothbrushes or a razor, since the long bays suit both.
Questions about this file
Can the bays hold toiletries too?
Yes, each bay runs the full depth, so toothbrushes, a razor or a slim tube stand in them as easily as skincare bottles.
Will it survive a wet counter?
If every face and cut edge is sealed with water-resistant varnish or oil, it handles splashes; do not leave it standing in water.
Which thickness do you recommend?
4 mm plywood is a good fit for a box this size; 3 mm cuts faster on a diode laser and is still stiff enough.
Can I scale it up for taller bottles?
Scale the drawing and then set every slot back to your sheet thickness, otherwise the tabs will be loose or will not fit.
Can I add engraving?
The file is cut-only. Add a name or a small motif to the front panel in your laser software.
Similar files
