VisualizationJewelry Row Tray SVG, Six Slot Earring and Ring Organizer DXF, Sloped Dresser Accessory Tray Laser Cut File
A sloped jewelry tray with six narrow slots in a single row, one each for earrings, rings, bracelets, a watch, sunglasses and hoops. It measures 380 × 170 × 80 mm (14.96 × 6.69 × 3.15 in), is cut from 10 pieces that lock together with tabs and slots, and the free download has SVG and DXF files for 3, 4, 5 and 6 mm plywood.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 380 × 170 × 80 mm (14.96 × 6.69 × 3.15 in)
- Parts
- 10
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,504 × 262 mm
- Cut length
- 7.42 m
- Est. time, 10 W diode (3 mm)
- 24 min 44 s
- Est. time, 40 W CO2 (3 mm)
- 10 min 18 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the 3, 4, 5 or 6 mm file and cut one divider with a matching slot on scrap to judge the fit.
- 02Cut the ten parts, grouping the five identical dividers on one sheet and the walls and base on others.
- 03Set all five dividers into the base, add the 80 mm back to align them, then the two sloped sides and the 56 mm front.
- 04Sand the divider tops, oil the tray and make felt ring rolls or earring cushions to fit the narrow slots.
Six slots, one row
Five dividers run front to back and split the 380 mm length into six slim slots of similar width. There are no cross dividers, so every slot is open from back to front and each kind of jewelry gets its own lane. This is the most slots in a single row among these trays, which makes it a good fit for people who sort strictly by type.
The photo shows the order many people use: an earring cushion with pearl drops and crystal studs, a ring roll, pearl and chain bracelets standing on edge, a watch, sunglasses folded upright and a pair of gold hoops with a cuff. The back wall is 80 mm and the front 56 mm, so the taller items at the back of each slot stay visible.
Cutting and assembly
Ten parts: front, back, two sloped sides, base and five dividers. Expect about 24 min 44 s on a 10 W diode, about 10 min 18 s on a 40 W CO2 and about 4 min 57 s on a 100 W CO2 for the 3 mm file. The nested layout is 1504 × 262 mm. The five dividers are identical, so on a small bed they nest neatly on one sheet, with the long walls and base on two more.
Stand the five dividers in the base, then add the back so they line up, followed by the sides and front. Tabs hold the tray square; glue is only needed if you want it permanent. On a diode laser, 3 mm cuts in one or two passes, while the 5 and 6 mm versions call for several passes or a CO2 machine.
Finishing and gift ideas
Sand the divider tops lightly so they do not catch on chains, then wipe on clear oil. Felt-wrapped ring rolls and earring cushions cut to the slot width turn it into a proper jewelry case. It makes a thoughtful gift for a teenager starting a jewelry collection, or a tidy dresser tray sold in pairs with a matching ring dish.
Questions about this file
How wide is each of the six slots?
The 380 mm length is split into six lanes of similar width, roughly 55 to 60 mm each, enough for a watch, a ring roll or folded sunglasses standing upright.
Can I remove a divider to get one wider slot?
Yes, just leave one divider out. The empty slots in the base and walls stay visible, so you may want to sand or fill them.
Can I cut it in acrylic for a shop display?
Yes, use the file matching your acrylic thickness and glue the joints with acrylic cement. Clear or frosted acrylic looks clean on a counter.
Is 3 mm plywood strong enough for this many dividers?
Yes. The five dividers brace the walls, so even 3 mm birch makes a rigid tray.
How do I make ring rolls for the slots?
Roll strips of felt around foam or cotton, cut them to the 170 mm depth and press them into one slot; rings push into the gaps.
Similar files
