VisualizationJewelry Tray SVG, Watch and Sunglasses Channel Organizer DXF, Three Cubby Earring and Ring Tray Laser Cut File
A gently sloped jewelry tray with a long full-width channel at the back for a watch and sunglasses and three cubbies in front for earrings, rings and bracelets. It measures 380 × 210 × 70 mm (14.96 × 8.27 × 2.76 in), uses 8 pieces with tab-and-slot joints, and the free download includes SVG and DXF for 3, 4, 5 and 6 mm plywood.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 380 × 210 × 70 mm (14.96 × 8.27 × 2.76 in)
- Parts
- 8
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,200 × 292 mm
- Cut length
- 6.58 m
- Est. time, 10 W diode (3 mm)
- 21 min 56 s
- Est. time, 40 W CO2 (3 mm)
- 9 min 08 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Pick the file for your plywood thickness and cut one slot on an offcut to check the tab fit.
- 02Cut the eight parts over two or three sheets, keeping the 380 mm pieces whole.
- 03Attach the two short dividers to the front face of the cross divider, set it on the base and add the four walls, finishing with the 63 mm front.
- 04Sand, oil, and put the watch and sunglasses in the back channel and small jewelry in the three front cubbies.
Channel at the back, cubbies in front
A cross divider runs the full 380 mm length and is as tall as the 70 mm back wall. Behind it is one long open channel; in front, two short dividers create three cubbies. This is the reverse of the trays where small cubbies sit at the back: here the long items are behind and the small ones within easy reach.
The back channel fits a watch on its strap and a pair of sunglasses side by side. The front cubbies hold pearl drops and hoops, two rings, and a bracelet with a bangle in the photo. The front wall is 63 mm, only a little lower than the 70 mm back, so the slope is gentle and the tray looks almost square from the side.
Laser time and sheet
Eight pieces: front, back, two sides, base, cross divider and two short dividers. For the 3 mm file, cutting takes about 21 min 56 s on a 10 W diode, about 9 min 08 s on a 40 W CO2 and about 4 min 23 s on a 100 W CO2. The nested layout is 1200 × 292 mm. On a 400 mm bed, cut the base and long pieces on separate sheets.
For a dresser, 3 mm or 4 mm birch is light and neat. Choose 5 or 6 mm if the tray will be carried around or used as a shop display, but plan on a CO2 laser or extra passes on a diode.
Assembly and finish
Fit the two short dividers to the cross divider, place it on the base, then add back, sides and front. Glue is optional. Sand the top edges and finish with clear oil; on a wooden desk like the one in the photo, a light oil makes the birch blend with the furniture.
Questions about this file
Is the long back channel wide enough for sunglasses?
Yes. It runs the full length of the tray, so a folded pair lies flat next to a watch.
How sloped is the front?
Only slightly: 63 mm at the front against 70 mm at the back. It is the gentlest slope among these jewelry trays.
Can I flip the layout so the cubbies are at the back?
Yes, just turn the cross divider assembly around before fitting it to the base; the slots are symmetrical front to back.
Do I need glue?
No, the joints hold by friction. Glue helps only if the tray is moved a lot or shipped assembled.
Is it suitable for a bathroom shelf?
Yes, if you seal every face, including the underside of the base, with polyurethane or hard-wax oil and keep it away from standing water.
Similar files
