VisualizationHeadband Holder SVG, Six Slot Hair Accessory Organizer, Upright Laser Cut Headband Storage Box DXF
A plywood headband holder with six upright slots side by side, 340 × 180 × 90 mm (13.39 × 7.09 × 3.54 in), whose sides slope steeply from 90 mm at the back to 54 mm at the front. You get free SVG and DXF files for 3, 4, 5 and 6 mm plywood; the 10 parts join with tabs and slots.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 340 × 180 × 90 mm (13.39 × 7.09 × 3.54 in)
- Parts
- 10
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,268 × 282 mm
- Cut length
- 7.40 m
- Est. time, 10 W diode (3 mm)
- 24 min 40 s
- Est. time, 40 W CO2 (3 mm)
- 10 min 17 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the file for your plywood thickness and test one divider slot on scrap; all five dividers share the same fit.
- 02Cut the 10 parts, splitting the 1268 mm layout so the five dividers stay on one sheet.
- 03Fit the sides and back to the base, add the five dividers one at a time and close with the 54 mm front.
- 04Sand the divider tops smooth, finish with lacquer and stand one headband or accessory group in each slot.
Upright slots for headbands
Five identical dividers run the full depth and cut the box into six equal slots, each a little over 50 mm wide. That width is the point: a headband stands upright in its own slot, so you can see the whole collection from the front like books on a shelf. In the photo three slots hold headbands (a beige padded one, a black one and a leopard print), and the others take scrunchies, claw clips with pearl and bobby pins, and a wide comb.
The steep slope, 90 mm to 54 mm, matters here more than on wider boxes: it lowers the front enough that you can pull a headband straight out without lifting it over the wall.
Cutting five identical dividers
With 10 parts and many long divider cuts, the 3 mm layout is 1268 mm long, so most diode machines will need two or three sheets. Cut times for the 3 mm file are about 24 min 40 s on a 10 W diode, about 10 min 17 s on a 40 W CO2 and about 4 min 56 s on a 100 W CO2. Since all five dividers are the same, a slight kerf difference affects every slot equally; test one slot on scrap and adjust power or speed before the run. Thicker 5–6 mm plywood looks great on a headband holder, but plan it for a CO2 laser.
Assembly is simple: base, sides, back, then the five dividers one by one, then the front. The dividers keep the box very square.
Smooth tops and listing ideas
Sand the top of each divider well; headbands rub against them every time you take one out. A clear lacquer is enough for a bedroom or a dry bathroom counter like the one shown. Listing ideas: a headband display for a hair accessory shop, a gift for someone with a large headband collection, or a two-box set side by side for twelve slots.
Questions about this file
How wide is each slot?
The 340 mm width is split into six equal slots of a little over 50 mm each, which suits most headbands standing upright.
Will wide padded headbands fit?
Most padded headbands fit in one slot. Very wide ones can go in a slot on their own or replace a scrunchie slot.
Can I make it longer with more slots?
Yes, extend the drawing and add dividers, keeping the slot width the same as your plywood thickness.
Is it safe to use on a bathroom counter?
Seal it with polyurethane or hard wax oil first and keep it away from standing water.
Which thickness looks best for a headband holder?
4 mm gives the dividers a solid feel and still cuts on a strong diode. 5 and 6 mm look chunkier but are a job for a CO2 laser.
Similar files
