VisualizationHair Accessory Tray SVG, Scrunchie and Headband Bins With Clip Ledge, Laser Cut Plywood Organizer DXF
A plywood hair accessory tray, 320 × 220 × 80 mm (12.60 × 8.66 × 3.15 in), with two deep bins at the back and one long, very low strip across the front, which is only 36 mm high. SVG and DXF files for 3, 4, 5 and 6 mm plywood are included; the 7 parts fit together with tabs and slots. The whole set of files is free to download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 320 × 220 × 80 mm (12.60 × 8.66 × 3.15 in)
- Parts
- 7
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,100 × 312 mm
- Cut length
- 5.68 m
- Est. time, 10 W diode (3 mm)
- 18 min 57 s
- Est. time, 40 W CO2 (3 mm)
- 7 min 54 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Start with the file sized for your sheet (3, 4, 5 or 6 mm) and check the fit on one cross divider slot cut from an offcut.
- 02Cut the 7 parts, putting the 320 × 220 mm base on its own sheet if the layout is too long.
- 03Fit the sides and back to the base, add the full-width cross divider and the single back divider, then the 36 mm front.
- 04Sand, finish with clear lacquer, fill the back bins with scrunchies and headbands and lay clips and a comb on the front ledge.
Two bins and a front ledge
This tray has the lowest front of the whole hair range: just 36 mm against an 80 mm back. A full-height cross divider stands a short way in from the front, and behind it one divider makes two deep bins. The left bin takes a heap of scrunchies, the right one stands a couple of headbands against the back wall. The narrow strip in front works like a ledge for the things you grab daily: a claw clip, a clear clip, a few bobby pins and a wooden comb lying flat.
That mix of deep bins and an open ledge suits a dressing table where some items are stored and others are used every morning.
Material and cutting
The 3 mm file needs about 18 min 57 s on a 10 W diode, about 7 min 54 s on a 40 W CO2 and about 3 min 47 s on a 100 W CO2. A 10 W diode handles 3 mm in one or two passes, while 6 mm takes several slow passes and leaves darker edges, so a CO2 is kinder to the thicker versions. With 7 parts it is quick to build. The full layout is 1100 mm long; on smaller machines, cut the base by itself and the walls and dividers on a second sheet.
Build order: sides and back into the base, the full-width cross divider, the single back divider, then the low front. Glue is not needed, but it does make the low front stiffer.
Selling and set ideas
Because the front ledge shows its contents, the tray looks good in listing photos with a few clips laid out on it. Sell it as a morning routine tray, or as a set of two with the same box made in a darker stain.
Questions about this file
What is the low front strip for?
It is a shallow ledge for items you use every day, like a claw clip, a comb and a few pins, so they are always in reach.
Are the back bins deep enough for headbands?
Yes, the cross divider is full height at 80 mm, so headbands stand upright behind it.
Can I make the front higher?
You can redraw the side profile and front panel. Keep the tab positions and slot widths matching your plywood.
Is 3 mm plywood stiff enough for such a low front?
Yes, the low front is held by the sides and base tabs on both ends; glue makes it stiffer if you like.
Will the comb slide off the low ledge?
No, the 36 mm front wall still stops a flat comb or clip from sliding out, while keeping it easy to pick up.
Similar files
