VisualizationScrunchie Organizer SVG, Claw Clip Holder Box, Four Slot Laser Cut Hair Accessory Organizer DXF
A four-slot plywood organizer for scrunchies, claw clips, bobby pins and headbands, 360 × 200 × 90 mm (14.17 × 7.87 × 3.54 in), with all slots side by side and sides sloping from 90 mm down to 58 mm. Free SVG and DXF files for 3, 4, 5 and 6 mm plywood, 8 parts with tab-and-slot joints.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 360 × 200 × 90 mm (14.17 × 7.87 × 3.54 in)
- Parts
- 8
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,140 × 302 mm
- Cut length
- 6.38 m
- Est. time, 10 W diode (3 mm)
- 21 min 16 s
- Est. time, 40 W CO2 (3 mm)
- 8 min 52 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the 3, 4, 5 or 6 mm version and cut one divider slot on scrap to check your plywood thickness.
- 02Cut the 8 parts; the three dividers are identical, so you can cut spares.
- 03Assemble base, sloped sides and back, slide in the three dividers, then add the 58 mm front.
- 04Sand, oil or stain the box and put bobby pins in the slim slot, scrunchies and claw clips in the wide ones.
Four slots, four jobs
Three full-depth dividers run front to back and split the box into four slots of different widths. On the far left is a slim slot just wide enough for a bundle of bobby pins standing upright. Next comes a wide slot for satin scrunchies, then another wide one for big claw clips, and on the right a slot where a comb and a couple of headbands stand on edge against the back. Because every slot runs the full 200 mm depth, long items fit without bending.
The back is 90 mm, among the taller ones in this range, and the front is 58 mm, so the slope is steep enough to see into each slot from a bedside table or dresser.
From sheet to box
Estimated cut time for the 3 mm file: about 21 min 16 s on a 10 W diode, about 8 min 52 s on a 40 W CO2, about 4 min 15 s on a 100 W CO2. The three dividers are the same shape, which saves sorting. On a machine with a bed under 1140 mm, cut the base and back first, then the rest. A diode cuts 3 mm in about two passes; the 6 mm file is better suited to a 40 W or stronger CO2.
To build: base, sides, back, the three dividers in any order, then the front. It is rigid without glue.
Finishing and gifting
Sand the slot rims and seal with clear oil. For a warmer look, a light walnut stain suits a bedroom like the one in the photo. Fill it with two scrunchies, two claw clips and a pack of pins as a birthday gift, or sell it as part of a bedroom set with a jewellery tray.
Questions about this file
What is the slim slot on the left for?
It holds bobby pins or hair pins standing upright, so they do not mix with bigger accessories.
Can large claw clips stand up inside?
Yes, the slots are 90 mm tall at the back, so even large claw clips stand without sticking out much.
Can I resize the slots?
You can move the dividers by editing the slots in the base, front and back. Keep every slot as wide as your sheet is thick.
Is MDF a good choice?
MDF works for a bedroom box and takes paint well. Plywood is the better choice if it may get damp.
How should I finish it for a bedside table?
Clear oil or a light walnut stain both work. Wipe off excess stain before it dries so the slots stay clean.
Similar files
