VisualizationSquare Skincare Organizer SVG, Compact Four Cell Desk Caddy Laser Cut File, Small Cosmetic Box DXF
A compact, nearly square skincare organizer with four cells in a two-by-two grid, provided as SVG and DXF with separate files for 3, 4, 5 and 6 mm plywood. It measures 240 × 230 × 100 mm (9.45 × 9.06 × 3.94 in), is made from 8 pieces, and its sides slope from the 100 mm back to a 55 mm front. Tabs and slots hold it together, and the download is free.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 240 × 230 × 100 mm (9.45 × 9.06 × 3.94 in)
- Parts
- 8
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 960 × 342 mm
- Cut length
- 5.53 m
- Est. time, 10 W diode (3 mm)
- 18 min 26 s
- Est. time, 40 W CO2 (3 mm)
- 7 min 41 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Download the SVG or DXF for your sheet thickness and test-cut one slot in a scrap of the same plywood.
- 02Cut all 8 pieces, including the square base, the cross divider and the two short dividers.
- 03Fit the cross divider and the two short dividers into the base, then attach the back, both sloped sides and the low front.
- 04Smooth the edges with fine sandpaper, oil or lacquer the box, and fill the four cells with masks, serums, creams and pads.
A small footprint with four cells
At 240 mm wide and 230 mm deep, this is the most compact box in the skincare group, made for a narrow desk corner, a bedside table or a shelf beside the mirror. One cross divider and two short dividers form a simple two-by-two grid. The back pair sits higher, the front pair lower, following the slope of the sides.
In the photo, the back left cell holds a stack of sheet masks and the back right one two dropper serums. The front left cell takes a large and a small cream jar, and the front right one a pile of cotton pads. Four cells suits a short morning routine: cleanser, serum, cream and pads.
Cutting notes
The 3 mm layout measures 960 × 342 mm. Owners of a smaller machine can move the square base to a second sheet and keep the walls together on the first. Cutting the 3 mm file takes about 18 min 26 s on a 10 W diode, about 7 min 41 s on a 40 W CO2 and about 3 min 41 s on a 100 W CO2. For 5 or 6 mm stock, a diode will need several passes, so a CO2 is the faster choice.
Build order: cross divider into the base, the two short dividers on either side of it, then the back, the sides and finally the front.
Make it a set
Because the box is almost square, two of them sit side by side on a deeper vanity without a gap, or one fits inside a drawer. Cut a second one in 4 mm plywood for a partner, or sell a pair as his-and-hers organizers in two finishes: natural oil and white stain.
Questions about this file
Is this box small enough for a bedside table?
Yes. Its footprint is 240 × 230 mm, about the size of a large book, so it fits most nightstands.
Can I scale it up to fit bigger bottles?
You can enlarge the drawing, but the slots will grow too, so redraw them to your material thickness afterwards. The simpler route is to keep the size and use the cells for shorter jars.
Should I glue it?
Glue is not needed for the box to stand. Add wood glue only if you want it to stay assembled for good or plan to ship it.
Which thickness looks best for this compact size?
3 or 4 mm keeps a small box light and neat; 6 mm walls take noticeable space out of each cell.
Can it be cut from MDF?
Yes, use the file matching the MDF thickness and paint or seal it, since raw MDF marks easily with water and oils.
Similar files
