VisualizationNarrow Jewelry Tray SVG, Long Shelf Organizer DXF, Five Slot Bathroom Counter Jewelry Holder Laser Cut File
A long, narrow jewelry tray with five slots in a single row and a sloped front, sized for a shelf or bathroom counter: earrings, rings, bracelets, a watch and sunglasses each get their own slot. It measures 440 × 130 × 80 mm (17.32 × 5.12 × 3.15 in), is cut from 9 pieces that fit with tabs and slots, and the free download has SVG and DXF for 3, 4, 5 and 6 mm plywood.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 440 × 130 × 80 mm (17.32 × 5.12 × 3.15 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,738 × 222 mm
- Cut length
- 6.55 m
- Est. time, 10 W diode (3 mm)
- 21 min 50 s
- Est. time, 40 W CO2 (3 mm)
- 9 min 06 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Confirm your laser bed takes 440 mm parts, pick the 3, 4, 5 or 6 mm file and cut a test slot.
- 02Cut the nine parts, arranging the 1738 mm layout across several sheets with the long pieces lengthwise.
- 03Set the four dividers into the base, add the 80 mm back to hold them upright, then the sides and the 56 mm front.
- 04Seal with polyurethane if it goes near a sink, and give each of the five slots one kind of jewelry.
Built for narrow spaces
At only 130 mm deep this tray fits where wider ones do not: a bathroom counter between sink and wall, a windowsill, a narrow shelf above a dresser. Four dividers run front to back and split the 440 mm length into five slots in a row. Every slot is open to the front, so nothing hides behind anything else.
The photo shows one slot each for hoops and pearl studs, rings, a pearl bracelet and a bangle, a watch on a mesh strap and a pair of sunglasses. The back is 80 mm and the front 56 mm, enough of a slope to see into each slot from above.
Length matters when cutting
The front, back and base are 440 mm long, so check your bed before you start: many diode machines are 400 mm wide, which is too short for those pieces at this size. The full layout is 1738 × 222 mm.
Times for the 3 mm file: about 21 min 50 s on a 10 W diode, about 9 min 06 s on a 40 W CO2 and about 4 min 22 s on a 100 W CO2. Diode users should stay with 3 or 4 mm unless they are prepared for multiple passes on 5 and 6 mm.
Assembly and sets
Slide all four dividers into the base, then add the back so they stand straight. Fit the sides and close with the front. The tab-and-slot joints hold firmly; a little glue helps if the tray will sit near water.
Pair this narrow tray with a matching soap dish or a toothbrush holder for a bathroom counter set, or sell it in two finishes: natural birch and white-washed. For a bathroom, seal every face with polyurethane or hard-wax oil.
Questions about this file
Will it fit on a narrow bathroom counter?
It is only 130 mm deep, which suits the strip between a sink and the wall or a narrow shelf.
My laser bed is 400 mm. Can I cut this?
Not at full size, since the front, back and base are 440 mm long. Either scale it down and keep the slots at your plywood thickness, or cut the long parts on a bigger machine.
How do I make it water resistant?
Seal all faces with water-based polyurethane or hard-wax oil, two coats, and let it cure before use. Wipe off splashes rather than letting them sit.
Can I cut it in acrylic?
Yes, with the file that matches your acrylic thickness. Acrylic suits bathrooms well because it does not absorb water.
What should go in each slot?
One type per slot works best: earrings, rings, bracelets, a watch and sunglasses, as in the photo.
Similar files
