VisualizationNarrow Hair Accessory Caddy SVG, Five Slot Shelf Organizer, Laser Cut Headband and Comb Holder DXF
A long, narrow plywood caddy for hair accessories, 400 × 140 × 90 mm (15.75 × 5.51 × 3.54 in), with five slots in a single row and sides that slope from 90 mm to a 72 mm front. The free download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; 9 parts assemble with tabs and slots.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 400 × 140 × 90 mm (15.75 × 5.51 × 3.54 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,504 × 242 mm
- Cut length
- 6.65 m
- Est. time, 10 W diode (3 mm)
- 22 min 10 s
- Est. time, 40 W CO2 (3 mm)
- 9 min 14 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Pick the file for your plywood thickness and check one divider slot on scrap before cutting the long parts.
- 02Cut the 9 parts, placing the three 400 mm panels together on one sheet if your bed is short.
- 03Fit the sides and back to the base, slide in the four identical dividers, then add the front and check it sits flat.
- 04Sand, seal with hard wax oil or lacquer and line up scrunchies, clips, pins, headbands and a comb in the five slots.
Built for shelves and window sills
Only 140 mm deep but 400 mm long, this caddy fits where a square box would not: a narrow bathroom shelf, the back of a sink counter or a window sill. Four dividers make five equal slots in one line, each about 80 mm wide. Left to right in the photo: scrunchies, claw clips, bobby pins, two headbands standing on edge, and a comb. Every slot is open to the front, so nothing hides behind anything else.
Bed size and assembly
The parts are long and thin, and the 3 mm layout is 1504 mm long, longer than many desktop machines. Rearrange them: the base, front and back are each 400 mm, so lay them side by side on one sheet and the sides and dividers on a second. The 3 mm file is estimated at about 22 min 10 s on a 10 W diode, about 9 min 14 s on a 40 W CO2 and about 4 min 26 s on a 100 W CO2. Use 3 or 4 mm on a diode; 5 or 6 mm is a CO2 job unless you accept several passes.
Base first, then both sides and the back. The four dividers are identical, so it does not matter which goes where; slide them in and add the front. A long, narrow box can twist slightly before the front is on, so check it sits flat. Glue the corners if you want it completely rigid.
Bathroom finish and selling ideas
Sand all edges and coat with a water-resistant finish such as hard wax oil. Keep it on a shelf rather than right next to the tap.
Long narrow caddies are popular for small bathrooms and RVs. Offer a stained version, or a pair: one for hair accessories, one for skincare.
Questions about this file
Will it fit on a narrow bathroom shelf?
It needs only 140 mm of depth, so most bathroom shelves and wide window sills can take it.
Are the five slots the same size?
Yes, the four dividers are identical and evenly spaced, so the slots are all the same width.
Can I shorten it to three slots?
You can edit the drawing to a shorter length and remove two dividers. Keep the slot widths equal to your plywood thickness after editing.
How do I stop water damage near a sink?
Seal every face and edge with a waterproof finish and wipe off splashes. Do not leave it standing in water.
Can I add a name on the long front?
Yes, the 400 mm front has room for a name. Add it as an engrave layer yourself; the file has no engraving.
Similar files
