VisualizationNarrow Skincare Organizer SVG, Long Five Slot Shelf Tray Laser Cut File, Slim Vanity Ledge Box DXF
A long, narrow skincare organizer with five slots in one row, made for shelves, window ledges and slim vanities, and supplied as SVG and DXF with separate files for 3, 4, 5 and 6 mm plywood. It measures 380 × 130 × 110 mm (14.96 × 5.12 × 4.33 in), is cut from 9 pieces, and its sides slope to a 61 mm front. It joins with tabs and slots and is free to download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 380 × 130 × 110 mm (14.96 × 5.12 × 4.33 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,424 × 252 mm
- Cut length
- 6.51 m
- Est. time, 10 W diode (3 mm)
- 21 min 42 s
- Est. time, 40 W CO2 (3 mm)
- 9 min 03 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Pick the file for your plywood and test-cut one slot; check that your bed fits the 380 mm long parts.
- 02Cut the 9 parts: front, back, two sloped sides, base and four dividers.
- 03Stand the four dividers in the base, attach the back and both sides, and finish with the 61 mm front.
- 04Sand and finish, then fill the five slots in a row, tallest items toward the middle or the ends as you prefer.
Made for slim spaces
At only 130 mm deep, this is the slimmest box in the skincare set, yet at 380 mm it is one of the longest. Four full-height dividers split it into five slots in a single row, so it fits a bathroom shelf, the ledge under a mirror or the back edge of a narrow dressing table where a deeper tray would stick out.
The photo shows a vanity next to a boucle pouf. From left to right the slots hold two cream jars, a pair of serum droppers, a stack of sheet masks, cotton pads and two small jars. The front wall here is 61 mm, a little taller than on most boxes in the set, which helps keep things in place on a shelf.
Fitting the long layout on your laser
Because the pieces are long and thin, the 3 mm layout is 1424 × 252 mm. The front, back and base are each 380 mm long, so they need a bed at least that wide, but the sides and dividers are short and can fill the space beside them on a second sheet. Cutting time for the 3 mm file is about 21 min 42 s on a 10 W diode, about 9 min 03 s on a 40 W CO2 and about 4 min 20 s on a 100 W CO2. A diode needs extra passes for 5 or 6 mm.
Assembly
Set the four dividers in the base, add the back, then the two sloped sides, and close it with the front. A drop of glue in each divider slot keeps the long box from flexing.
Two of these end to end make a tidy display along a bathroom shelf, and the slim shape posts cheaply when sold flat-packed.
Questions about this file
Will it fit on a narrow bathroom shelf?
It is 130 mm deep, so it sits on most shelves and window ledges that are at least 13 cm deep.
What is the smallest laser bed I need?
The front, back and base are 380 mm long, so your bed must take that length; other parts can go on a second sheet.
Can I make it shorter with fewer slots?
Remove one divider and shorten the front, back and base by one slot width in your software, keeping slot sizes equal to your sheet.
Can it be shipped flat-packed?
Yes, all parts are flat and the box assembles without glue, so it can travel in a slim envelope and be put together on arrival.
Which thickness is best for a long box?
4 or 5 mm plywood keeps the long walls straight; 3 mm works too if you glue the divider slots.
Similar files
