VisualizationLarge Hair Organizer SVG, Two Row Headband and Scrunchie Box, Laser Cut Hair Accessory Tray DXF
A large two-row plywood organizer for hair accessories, 360 × 240 × 80 mm (14.17 × 9.45 × 3.15 in): two bays at the back for headbands and combs, three pockets in front for pins, scrunchies and clips, with a 44 mm front. The free download includes SVG and DXF for 3, 4, 5 and 6 mm plywood, 9 parts joined by tabs and slots.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 360 × 240 × 80 mm (14.17 × 9.45 × 3.15 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,220 × 332 mm
- Cut length
- 7.14 m
- Est. time, 10 W diode (3 mm)
- 23 min 48 s
- Est. time, 40 W CO2 (3 mm)
- 9 min 55 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Use the SVG or DXF for your plywood and check the fit by cutting one front divider slot on scrap.
- 02Cut the 9 parts; give the 360 × 240 mm base its own sheet on smaller lasers.
- 03Assemble base, sides and back, add the cross divider and the single back divider, then the two front dividers and the front panel.
- 04Sand, oil or white-wash, and put headbands and a comb in the back bays and pins, scrunchies and clips in front.
Room for a big collection
At 360 × 240 mm this is one of the biggest boxes in the hair range, with a footprint that suits a dressing room counter or a large vanity. A cross divider splits it into a back row and a front row. The back row has two bays: a wide one on the left for a stack of headbands and a smaller one on the right for a comb. The front row is split into three: a narrow pocket on the left for pearl-topped pins, a wide middle pocket for scrunchies and a right pocket for claw clips.
The 44 mm front sits far below the 80 mm back, so the front pockets are open and easy to see into while the back bays keep tall items upright.
Which plywood and laser
The 3 mm file is estimated at about 23 min 48 s on a 10 W diode, about 9 min 55 s on a 40 W CO2 and about 4 min 46 s on a 100 W CO2. A diode does 3 mm cleanly in one or two passes; for a large box like this, 4 mm adds stiffness and still cuts on a 20 W diode or any CO2. 5 and 6 mm are best left to CO2 machines. The layout is 1220 × 332 mm, so on a typical desktop machine the base needs a sheet of its own.
Build it in this order: base, sides, back, cross divider, the back-row divider, the two front dividers, then the front. A drop of glue under the base corners helps a large box stay flat.
Finishing ideas
Clear oil keeps the natural birch look in a bright room; a white wash suits a minimal dressing room. Offer it to customers with big collections, or as a shared organizer for two sisters with one row each.
Questions about this file
How big is this compared with the other hair boxes?
It is 360 mm wide and 240 mm deep, one of the largest footprints in the range, made for bigger collections.
What is the narrow front pocket for?
It is sized for hair pins and bobby pins standing upright, so they stay separate from scrunchies and clips.
Should I use thicker plywood for a large box?
4 mm is a good middle ground; it is stiffer than 3 mm but still quick to cut. 5 or 6 mm is very sturdy but needs a CO2.
Can I cut it from MDF?
Yes, MDF cuts well and paints nicely. Seal it if the box will be used in a bathroom.
Can I add a family name for a shared organizer?
Yes, add the name to the front panel as an engraving in your laser software. The file contains only cut lines.
Similar files
