VisualizationJewelry Organizer Box SVG, Center Bay Watch and Sunglasses Holder DXF, Closet Jewelry Tray Laser Cut File
A deep, straight-walled jewelry box with a large center bay for sunglasses, a watch and bracelets and two smaller sections on each side for earrings and rings, five compartments in total. It measures 320 × 250 × 70 mm (12.6 × 9.84 × 2.76 in), consists of 9 tab-and-slot pieces and the free download has SVG and DXF files for 3, 4, 5 and 6 mm plywood.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 320 × 250 × 70 mm (12.60 × 9.84 × 2.76 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,160 × 332 mm
- Cut length
- 6.89 m
- Est. time, 10 W diode (3 mm)
- 22 min 59 s
- Est. time, 40 W CO2 (3 mm)
- 9 min 34 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Select the file for your plywood thickness and cut a single test slot to check the tab fit.
- 02Cut the nine pieces, keeping the 320 × 250 mm base on its own sheet.
- 03Join each short cross divider to its long divider, place both on the base and add the four straight walls.
- 04Sand, finish with oil or lacquer, and put larger pieces in the center bay and small ones in the four side sections.
Symmetrical layout around a center bay
Two long dividers run the full 250 mm depth and split the box into three columns. The middle column is left open as one large bay; each side column is cut in half by a short cross divider, giving two small sections on the left and two on the right. The left column is a little narrower than the right one.
The center bay is where the bigger daily pieces live: sunglasses, a watch, a pearl bracelet and a bangle in the photo. The left sections hold gold hoops and pearl drops, and the right ones rings and flower studs. At 250 mm deep, this is the deepest box in the jewelry set, which suits a dressing table or a closet island where there is room to spread out.
Cutting and materials
Nine parts: front, back, two sides, base, two long dividers and two short cross dividers. Run the job for the 3 mm file and expect about 22 min 59 s on a 10 W diode, about 9 min 34 s on a 40 W CO2 and about 4 min 36 s on a 100 W CO2. The layout is 1160 × 332 mm. The 320 × 250 mm base fits a 400 × 400 mm bed on its own; the walls and dividers go on two more sheets.
On a diode, 3 mm birch is the comfortable choice. The 6 mm file makes a heavy, sturdy box but expects a CO2 laser or a lot of passes.
Assembly and ideas
Fit the two cross dividers to the long dividers, set the frame on the base, then close it with the four 70 mm walls. The box is square and rigid without glue.
- Line the center bay with velvet and sell it as a watch and sunglasses valet.
- Make a matching smaller box for a closet shelf.
- Stain it dark for a men's dresser.
Questions about this file
What fits in the large center bay?
Sunglasses, a watch, bracelets or a phone. It runs the full 250 mm depth, so bigger items lie flat without overlapping.
Why are the two side columns different widths?
The left column is a little narrower than the right, so you get slightly different section sizes for earrings on one side and rings or studs on the other.
Can I put a lid on it?
The file has no lid. You could cut a flat panel the size of the outer box and rest it on top, but the walls have no grooves for a sliding lid.
Is MDF strong enough?
Yes, 4 to 6 mm MDF with the matching file makes a solid box. Paint it, since bare MDF edges look dull.
Will it fit on a closet shelf?
It needs a 320 × 250 mm footprint and 70 mm of height, so it fits most closet shelves and wide drawers.
Similar files
