VisualizationHair Clip Organizer SVG, Five Compartment Claw Clip Box, Laser Cut Hair Accessory Holder DXF
A five-compartment plywood organizer for hair clips, scrunchies and headbands, 340 × 200 × 80 mm (13.39 × 7.87 × 3.15 in), with a 64 mm front and sides that slope up to the back. The download contains SVG and DXF for 3, 4, 5 and 6 mm plywood; the 9 pieces join with tabs and slots. Both formats are free to download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 340 × 200 × 80 mm (13.39 × 7.87 × 3.15 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,100 × 292 mm
- Cut length
- 6.60 m
- Est. time, 10 W diode (3 mm)
- 22 min 00 s
- Est. time, 40 W CO2 (3 mm)
- 9 min 10 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Download the version for your plywood thickness and test one front-row divider slot on an offcut before cutting the whole sheet.
- 02Cut the 9 parts, splitting the 1100 mm layout across sheets if your bed is small.
- 03Assemble base, sides and back, then insert the long cross divider, the three short back dividers and finally the two front ones.
- 04Close it with the low front wall, sand the corners and fill the back pockets with clips, pins and a comb.
Layout of the five compartments
A full-length cross divider splits the box into two rows. The back row has three pockets of similar width: one for claw clips, a middle one for bobby pins and one for a comb. The front row has two larger bins, one for a stack of satin scrunchies and a longer one where headbands can lie flat. The front row dividers are a little lower than the back ones, so the box steps down toward you like the sloped sides.
At 340 mm wide and 80 mm tall it suits a vanity, a bathroom shelf or a large drawer.
Cutting and putting it together
All 9 parts come in four versions, so 3 mm plywood gets 3 mm slots and 6 mm gets 6 mm slots. For the 3 mm file the estimate is about 22 min 00 s on a 10 W diode, about 9 min 10 s on a 40 W CO2 and about 4 min 24 s on a 100 W CO2. A diode handles 3 mm comfortably in a pass or two; thicker sheets want a CO2 or extra passes with good air assist. The full layout is 1100 mm long, which means machines with a 400 mm bed need it split over three sheets.
Build the outer shell first: base, sides, back. Then slide the long cross divider in, followed by the three short back dividers and the two in front. Everything should press fit; a dot of glue on each divider foot stops rattling if the box is going to be shipped.
Make it a set
Pair it with a small tray for hair ties or a tall comb cup from the same plywood, finished the same way, and you have a matching vanity set that sells better as a bundle than one piece alone. A teen's room gift with a few clips inside is another easy idea.
Questions about this file
What goes in the three small back pockets?
Claw clips, bobby pins and a flat comb fit well. Each pocket is roughly a third of the width, so mid-size claw clips stand upright easily.
Can I use 3 mm MDF instead of plywood?
Yes, MDF cuts cleanly with the same file. It is less tolerant of moisture, so seal it if the box will sit near a sink.
Why do the front dividers look shorter?
They follow the slope of the sides, so the front row is lower and easier to reach into while the back row stays taller.
Does the box need glue?
No, the tabs and slots hold it together. Glue is only worth adding if you plan to ship it or want it fully rigid.
Can I engrave a name on the front?
The file contains cut lines only, but the 64 mm front panel has space for a short name or initials that you add in your laser software.
Similar files
