VisualizationCompact Hair Accessory Box SVG, Four Section Hair Clip Organizer, Small Wooden Bathroom Tray DXF
A small, almost square plywood box for hair accessories, 260 × 240 × 80 mm (10.24 × 9.45 × 3.15 in), divided into four equal compartments in a 2×2 grid, with a 64 mm front and sloped sides. The free files are SVG and DXF for 3, 4, 5 and 6 mm plywood, 8 parts joined by tabs and slots.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 260 × 240 × 80 mm (10.24 × 9.45 × 3.15 in)
- Parts
- 8
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,020 × 332 mm
- Cut length
- 5.68 m
- Est. time, 10 W diode (3 mm)
- 18 min 56 s
- Est. time, 40 W CO2 (3 mm)
- 7 min 53 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the 3, 4, 5 or 6 mm file and cut one test slot to make sure your plywood is the thickness the file expects.
- 02Cut the 8 parts; the base is the largest piece at 260 × 240 mm.
- 03Fit the sides and back into the base, add the cross divider, then the two short dividers, and close with the front.
- 04Seal with water-based polyurethane for a bathroom counter and sort clips, headbands, scrunchies and combs into the four squares.
Why a 2×2 grid
At only 260 mm wide this is one of the narrowest hair boxes we offer, but it is 240 mm deep, so each of the four squares is roomy. One cross divider and two short dividers make a simple grid: claw clips at the back left, headbands at the back right, scrunchies in front on the left and a comb with bobby pins at the front right. It fits on a bathroom counter beside a basin where a long tray would be in the way, and it is a good size for a child's or guest room.
Cutting and assembly order
The 3 mm layout is 1020 × 332 mm. On a 10 W diode the 3 mm file takes about 18 min 56 s; a 40 W CO2 does it in about 7 min 53 s and a 100 W CO2 in about 3 min 47 s. Plan on two or more passes per line on a diode for 5 or 6 mm stock, or cut those on a CO2. Because the base is close to square, it sits comfortably on most small beds once you move it to a sheet of its own.
- Base on the table, tabs up.
- Both sloped sides, then the back.
- Cross divider across the middle, then the taller back divider and the shorter front divider.
- Front wall last.
The press fit is firm enough for daily use. For a bathroom, brush on two thin coats of water-based polyurethane so splashes wipe off.
Small-box selling ideas
Small square boxes ship cheaply and photograph well with a few colourful clips inside. Offer it as a gift for a hairdresser's station, a stocking filler with matching scrunchies, or a set of two stacked side by side in a drawer.
Questions about this file
Is this box small enough for a narrow bathroom shelf?
It is 260 mm wide and 240 mm deep, so it needs a shelf at least 240 mm deep but takes little width.
Can I scale it down for kids’ hair clips?
Yes, but after scaling, reset the slot width to your plywood thickness. Shrinking the 3 mm file to 80% would leave 2.4 mm slots that 3 mm tabs cannot enter.
How do I protect it from water near a sink?
Two coats of water-based polyurethane or a hard wax oil keep splashes from soaking into the plywood edges.
Will 4 mm plywood look better than 3 mm?
4 mm gives a slightly sturdier, more solid look on a small box and still cuts well on a stronger diode or any CO2.
Can I put a monogram on it?
Nothing is engraved in the file, but you can add a monogram to the front or side panel in your own laser software before cutting.
Similar files
