VisualizationDeep Skincare Box SVG, Sheet Mask Organizer With Side Cells Laser Cut File, Wooden Face Care Caddy DXF
A deep skincare box with a full-depth center bay for sheet masks and two side columns each split into a back and a front cell, offered as SVG and DXF with separate files for 3, 4, 5 and 6 mm plywood. It measures 260 × 250 × 100 mm (10.24 × 9.84 × 3.94 in), uses 9 pieces, and slopes down to a 60 mm front. It assembles with tabs and slots, and downloading it is free.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 260 × 250 × 100 mm (10.24 × 9.84 × 3.94 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,040 × 362 mm
- Cut length
- 6.66 m
- Est. time, 10 W diode (3 mm)
- 22 min 13 s
- Est. time, 40 W CO2 (3 mm)
- 9 min 15 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Select the file for your plywood thickness and cut one test slot to confirm the fit.
- 02Cut the 9 parts: front, back, two sloped sides, base, two long dividers and two short cross dividers.
- 03Place both long dividers in the base, add a short cross divider to each side column, then fit the back, the sides and the 60 mm front.
- 04Sand, oil or lacquer, then load masks in the center bay and small bottles, jars and pads in the four side cells.
Symmetrical layout, masks in the middle
This box is almost as deep as it is wide, 250 mm front to back, which leaves room for a center bay long enough to hold a full stack of sheet masks upright with a cream jar in front of them. Two long dividers mark off that center bay. Each side column is then split by a short cross divider into a back cell and a front cell, giving five compartments arranged symmetrically.
In the photo, on a light wooden desk with a round mirror, the left column holds a serum at the back and cotton pads at the front; the right column has an amber serum behind and a white cream jar in front. The center bay carries the masks and a pink jar.
What to know before cutting
The download contains an SVG and a DXF for each of 3, 4, 5 and 6 mm plywood, with slots fitted to that thickness. The square-ish base makes the 3 mm layout 1040 × 362 mm; on a smaller bed, the base can go on its own sheet. For the 3 mm file allow about 22 min 13 s on a 10 W diode, about 9 min 15 s on a 40 W CO2 and about 4 min 27 s on a 100 W CO2. For 5 or 6 mm, use a CO2 or run more passes on a diode.
Assemble the long dividers first, then the two short cross dividers, then the back, the sides and the front.
Gift ideas
A sheet mask box makes an easy gift: fill the center bay with a week of masks, add a serum and pads to the side cells, and wrap it in clear film. For a Korean skincare shop, it also works as a counter display.
Questions about this file
Do standard sheet masks fit upright?
Yes, the center bay runs the full depth of the box and the back wall is 100 mm tall, so typical sheet mask sachets stand upright against it.
Can I scale it to make the center bay wider?
Scaling the whole drawing also changes slot widths, so after resizing set every slot back to your plywood thickness.
What thickness suits this box?
3 mm keeps the side cells roomy; 4 mm gives a sturdier box if you plan to sell or ship it.
Can I put a shop logo on it?
Yes, add an engraving to the front or the back panel in your laser software before cutting; the file itself has no engraving.
Does it need glue?
The tabs and slots hold it as is; glue is only for a permanent build.
Similar files
