VisualizationSquare Cosmetic Organizer SVG, Five Cell Makeup Box Laser File, Center Palette Bay Vanity Organizer DXF
A free download for a square cosmetic organizer, 240 × 240 × 90 mm (9.45 × 9.45 × 3.54 in), with five cells: a full-depth center bay flanked by two side columns that are each split into a back and a front cell. Its 9 plywood parts fit by tabs and slots, the sides slope from a 90 mm back to a 54 mm front, and SVG plus DXF files are supplied for 3, 4, 5 and 6 mm sheet.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 240 × 240 × 90 mm (9.45 × 9.45 × 3.54 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 980 × 342 mm
- Cut length
- 6.24 m
- Est. time, 10 W diode (3 mm)
- 20 min 49 s
- Est. time, 40 W CO2 (3 mm)
- 8 min 40 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose your sheet thickness, cut the matching file's test slot, and check that a long divider slides in with light pressure.
- 02Cut the nine pieces from the 980 × 342 mm layout, putting the 240 mm base on its own run if the bed is small.
- 03Set both long dividers into the base, add the narrow 51.6 mm and the wider 85.8 mm cross dividers in the side columns, then fit back, sides and front.
- 04Oil or lacquer the box and place palettes in the center bay, brushes and lipsticks in the side cells.
A center bay with split columns on both sides
Two long dividers run from the back to the front and divide the 240 mm square into three columns. The middle column stays open over the full depth, which is where palettes and a large compact go; in the photo two eyeshadow palettes stand one behind the other with a powder in front. The left column is narrow and has a short cross divider, giving a brush cell at the back and a lipstick cell in front. The right column is wider, about 8.6 cm, and is split the same way: lip products at the back and a cream compact at the front.
Laser time and sheet layout
The nine parts are arranged on 980 × 342 mm for the 3 mm file. The 240 mm square base is the largest piece; machines with a 300 mm short side can still take it, with the walls and dividers moved to a second run. Timing for the 3 mm file: about 20 min 49 s on a 10 W diode, about 8 min 40 s on a 40 W CO2, about 4 min 10 s on a 100 W CO2. Go for 3 or 4 mm on a diode; 5 and 6 mm cut cleaner on a CO2 tube.
Assembly, finish and set ideas
Fit the two long dividers into the base, then drop the 51.6 mm cross divider into the left column and the 85.8 mm one into the right column. Add the back, sides and 54 mm front. No glue is needed, though one drop per corner tab will stop it from racking.
A square footprint pairs well with other boxes:
- Two of these side by side fill a 48 cm vanity shelf
- Cut one in birch and one stained for a sister gift set
- Fill it with a mini skincare and lip kit for a holiday basket
Questions about this file
What size palette fits in the center bay?
The center bay runs the full 24 cm depth, so two medium palettes stand one behind the other, or one large palette lies at an angle. Very wide 18-pan palettes are too big.
Why is one side column narrower than the other?
The left column is meant for brushes and pencils, the right one for compacts and lipsticks, so their cross dividers are 51.6 mm and 85.8 mm long.
Could I cut it from 3 mm MDF and paint it?
Yes, use the 3 mm file. Prime the MDF edges before painting, because they soak up paint unevenly.
Which thickness should a diode owner choose?
3 mm is the safe choice for one or two passes on a 10 W diode. 4 mm works too with an extra pass and gives a sturdier square.
Can I put an initial on the front?
A single large initial or a short name fits the 240 mm front panel. Add it yourself as an engrave layer before you cut.
Similar files
