VisualizationMakeup Organizer SVG, Eight Compartment Cosmetic Storage Laser File, Large Wooden Vanity Organizer DXF
A free laser cut makeup organizer with eight compartments in two rows of four, 320 × 200 × 90 mm (12.60 × 7.87 × 3.54 in) outside. It is made from 12 plywood parts held by tabs and slots, with SVG and DXF files prepared separately for 3, 4, 5 and 6 mm plywood, and the sides slope down to a 50 mm front. It is free to download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 320 × 200 × 90 mm (12.60 × 7.87 × 3.54 in)
- Parts
- 12
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,276 × 302 mm
- Cut length
- 7.71 m
- Est. time, 10 W diode (3 mm)
- 25 min 42 s
- Est. time, 40 W CO2 (3 mm)
- 10 min 43 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Download the version for your sheet and test-fit one front-row divider before cutting all twelve parts.
- 02Split the 1276 × 302 mm layout over two or three sheets and keep the 90 mm and 69.7 mm dividers in separate piles.
- 03Join all six short dividers to the cross divider, lower the grid into the base, then add the back, sides and 50 mm front.
- 04Sand the many divider edges, seal, and give each of the eight cells one product type.
Eight cells for a full collection
This is the organizer with the most cells of the two-row designs: a cross divider 69.7 mm tall splits the 320 mm length into a back and a front row, and three short dividers in each row make four cells per row. Each cell is about 8 cm wide, enough for one product type per cell. On the marble vanity in the photo the back row holds brushes, lipsticks, a cushion compact and stacked eyeshadow quads; the front row has a powder, a palette, a bronzer and a blush. When every product has its own cell, you notice at once what is running out.
Sheet layout and cut time
Twelve parts make for a long nest: 1276 × 302 mm. Few hobby machines take that in one go, so divide the parts over two or three sheets; the base alone is 320 × 200 mm. Expect about 25 min 42 s for the 3 mm file on a 10 W diode, about 10 min 43 s on a 40 W CO2 and about 5 min 08 s on a 100 W CO2. With six short dividers, check that the back-row ones (90 mm) and the front-row ones (69.7 mm) do not get mixed up.
Assembly and selling
Fit the six short dividers onto the cross divider, place the grid in the base, then add the back, sides and the 50 mm front. Glue the outer corners if the box will travel. A dark walnut stain on the dividers with natural walls looks good in listing photos. Sellers often offer this size as a premium vanity organizer, while makeup artists use it as a station box for client kits.
Questions about this file
How much makeup does the eight-cell box hold?
Roughly a full personal collection: a set of brushes, five to eight lipsticks, three or four compacts and several palettes. Each cell is about 8 cm wide.
My laser bed is 400 mm wide. Can I still cut it?
Yes, rearrange the 12 parts over two or three sheets in your laser software; no part is longer than 320 mm.
Which thickness suits a 12-part box?
3 or 4 mm keeps the weight down and the cut time reasonable. 6 mm walls look solid, but the many dividers eat into the cells.
Will acrylic dividers fit the plywood walls?
Only if the acrylic sheet has the same real thickness as the plywood file you chose. Measure both with calipers, since 3 mm acrylic is often 2.8 or 3.2 mm.
Can a makeup artist add a studio logo?
Yes, put the logo as an engrave layer on the 320 mm front or on the back wall before assembly. The download itself has cut lines only.
Similar files
