VisualizationFeminine Care Box SVG, Compact Tampon and Pad Holder, Small Bathroom Organizer Laser File DXF
A compact four-compartment box for pads, tampons, panty liners and wipes, sized for a small bathroom shelf or sink corner. It comes as SVG and DXF in versions for 3, 4, 5 and 6 mm plywood, measures 280 × 220 × 110 mm (11.02 × 8.66 × 4.33 in), and assembles from 8 tab-and-slot pieces into a 2×2 grid with a sloped front. Downloading the files costs nothing.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 280 × 220 × 110 mm (11.02 × 8.66 × 4.33 in)
- Parts
- 8
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,020 × 342 mm
- Cut length
- 5.95 m
- Est. time, 10 W diode (3 mm)
- 19 min 51 s
- Est. time, 40 W CO2 (3 mm)
- 8 min 16 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Choose the file for your plywood thickness and cut one test slot; adjust power or speed until the tab slides in snugly.
- 02Cut the 8 pieces and pencil-mark the two cross dividers, because one is 3 mm longer than the other.
- 03Fit the long divider into the base, add each cross divider to its own side, then attach the back, the sloped sides and finally the low front.
- 04Sand, seal inside and out against shower steam, and fill the four squares with pads, tampons, liners and wipes.
Sized for a small bathroom
At 280 mm long and 220 mm deep, this box is closer to square than most organizers in this category, so it tucks into a sink corner or the end of a narrow shelf. One long divider runs front to back and two short cross dividers split each side, giving four equal-ish squares. In the photo the back pair holds pink pads and a row of tampons lying flat, while the front pair holds panty liners and a soft pack of intimate wipes. The front drops to 55 mm, so the front squares are easy to reach into while the back pair stays slightly hidden.
Assembly order
You will cut 8 parts: base, back, front, two sloped sides, one long divider and two cross dividers of slightly different lengths (141.5 mm and 138.5 mm). Keep them apart after cutting, since each fits only its own side of the long divider. Slot the long divider into the base, push one cross divider in on each side, then add the back and sides and finish with the low front. On a 10 W diode the 3 mm file needs about 19 min 51 s; a 40 W CO2 does it in about 8 min 16 s and a 100 W CO2 in about 3 min 58 s. The 3 mm layout is 1020 × 342 mm.
Finishing for damp rooms
Steam from the shower is harder on plywood than an occasional splash. Seal the inside faces as well as the outside, two thin coats of water-based polyurethane or a hardwood oil. A small version like this sells well as a dorm-room gift, or bundled into a "new home" bathroom set with a toothbrush stand.
Questions about this file
Will this 2×2 box fit on a narrow bathroom shelf?
It needs 280 mm of width and 220 mm of depth. If your shelf is shallower, scale the depth in your editor and keep the slot sizes unchanged.
Why is one cross divider 3 mm longer than the other?
The long divider is not exactly in the centre, so the left and right squares differ slightly. Mark them after cutting so each goes on its own side.
Will tampons lie flat in a back square?
Yes, regular and super tampons in wrappers lie across the square in a neat row, as shown in the photo.
Can I make it from 6 mm plywood?
Yes, there is a 6 mm file. It is heavier and more rigid, but a diode will need several passes, so a CO2 laser is the easier route.
How do I keep it from swelling in a steamy bathroom?
Seal all faces, including the base underside, with polyurethane or oil, and let it cure fully before putting paper-wrapped products inside.
Similar files
