Wide 3 Section Makeup Holder: Free DXF and SVG

Wide Makeup Holder SVG, Three Section Cosmetic Organizer Laser Cut File, Tall Back Brush and Palette Box DXF

A free download for a wide makeup holder with three long sections, 320 × 180 × 100 mm (12.60 × 7.09 × 3.94 in). It has 7 plywood parts that join with tabs and slots, a 100 mm back sloping down to a 55 mm front, and SVG and DXF cut files for 3, 4, 5 and 6 mm plywood.

Author

DXF World · 240 files

Formats

SVG, DXF

Outer size (W × D × H)

320 × 180 × 100 mm (12.60 × 7.09 × 3.94 in)

Parts

Material thickness

3, 4, 5 or 6 mm plywood (a file for each)

Layout size (3 mm file)

1,020 × 292 mm

Cut length

5.25 m

Est. time, 10 W diode (3 mm)

17 min 31 s

Est. time, 40 W CO2 (3 mm)

7 min 18 s

Layers

CUT only, no engraving

Free account required to download

How to make it

01Choose the file for your plywood and test one divider slot on an offcut.

02Cut the seven parts from the 1020 × 292 mm layout, moving the base and back to another sheet if needed.

03Push both dividers into the base, add the 100 mm back, fit the sides and finish with the 55 mm front.

04Sand the edges, oil the box and stand brushes, compacts and palettes in the three sections.

Bigger sections for bigger products

This holder follows the same three-section idea as the smaller slanted organizer, but it is 4 cm wider and 2 cm deeper, so each section is roughly 10 cm across and 18 cm deep. Two full-depth dividers form the sections. That extra room suits larger items: big powder compacts, a stack of palettes, a bottle of setting spray or a full brush set standing upright behind the 100 mm back. The bedroom vanity in the photo shows brushes, compacts, an eyeshadow palette with a blush and a row of lipsticks.

Choosing thickness and cutting

All seven parts nest on 1020 × 292 mm. If your machine is shorter, place the base and the back on a second sheet. Estimated laser time for the 3 mm file is about 17 min 31 s on a 10 W diode, about 7 min 18 s on a 40 W CO2 and about 3 min 30 s on a 100 W CO2. With fewer parts than most boxes in this set, the holder is a good candidate for 5 or 6 mm stock on a CO2: thick walls look solid on a wide box. On a 10 W diode stay with 3 or 4 mm.

Assembly and finishing touches

Seat both dividers in the base, press on the tall back, fit the two sides and close the box with the 55 mm front. The joints are tight enough to stay dry-fitted; glue makes it permanent. Break the sharp edges with sandpaper and apply a clear oil to bring out the birch grain.

Ideas: a wedding-day getting-ready box for the bride, a vanity gift with a set of brushes, or a larger companion to the smaller three-section model for a two-size Etsy listing.

Questions about this file

How wide is each of the three sections?

Each one is roughly 10 cm wide and runs the full 18 cm depth, enough for big compacts, palettes on edge or a full brush set.

How is it different from the smaller three-section organizer?

It is 320 × 180 mm instead of 280 × 160 mm and has a 55 mm front instead of 60 mm, so the sections are wider and deeper.

Is 6 mm plywood worth it here?

On a CO2 laser, yes: the box has only seven parts, so the extra cut time is small and the thick walls look solid. A diode needs several passes for 6 mm.

Will it hold up in a bathroom?

With a waterproof finish it will. Coat the base underside too, since that is where water collects on a counter.

Can I make it shorter for a low shelf?

Shortening the height means editing the back, front, sides and dividers while keeping the slot positions and widths. Scaling the whole drawing is not recommended because the slots would change.