VisualizationTulip SVG, Woodcut Tulip Bud Laser Cut File DXF, Spring Easter Ornament, Mother's Day Flower Gift
A closed tulip bud on a short stem, shown as a two-tone woodcut: the flower is engraved dark, and light shapes left in the wood mark the shine on the front petal, the edge of a second petal and a few flecks. Its footprint is 89 × 115.9 mm (3.5 × 4.56 in), with the 4 mm hole sitting in a small curl at the top.
- Formats
- SVG, DXF
- Size
- 89 × 116 mm (3.50 × 4.56 in)
- Parts
- 1
- Hanging hole
- 4 mm
- Cut length
- 0.41 m
- Engraving area
- 36.7 cm²
- Material
- 3 mm plywood, MDF or acrylic
- Est. time, 10 W diode
- 7 min 28 s
- Est. time, 40 W CO2
- 2 min 36 s
- Est. time, 100 W CO2
- 1 min 48 s
- Per 300 × 400 mm sheet
- 9 pcs
- Per 600 × 400 mm sheet
- 18 pcs
- Layers
- CUT (red), ENGRAVE (black)
- License
- CC0 1.0: free for personal and commercial use
Free account required to download
How to make it
- 01Import the tulip; the bud should read 89 by 115.9 mm, loop on top.
- 02Engrave the bloom and stem as a fill and make sure the small light flecks stay open.
- 03Cut along the bumpy outline and the top curl; one test cut shows whether the little loop holds.
- 04Paint the bud and stem, keep the highlights pale, and hang the tulip with ribbon.
Printed like a woodblock
The bud leans slightly, with a pointed petal opening on the left and a straight stem below. The picture is built from light and dark shapes rather than outlines: one tall pale streak runs down the front petal like a highlight, another marks the rim of a second petal, and small flecks scatter across the bloom. It looks like a print made from a carved block, so the ornament has a more grown-up, artistic feel than a cartoon flower. A little curl at the top joins the outline to the hanging hole.
Edges and highlights
Two areas need care. The flecks are tiny islands of bare wood inside the fill, and soft focus or high power can close them up. The outline has small bumps and that curl near the top, which the cut follows closely. Engraving dominates the job. Estimates in 3 mm plywood: 10 W diode, 7 min 28 s; 40 W CO2, 2 min 36 s; 100 W CO2, 1 min 48 s. A plain grid gives 9 tulips per 300 × 400 mm sheet and 18 per 600 × 400 mm.
Spring sales
- Easter and spring trees, painted red, yellow or pink.
- Mother's Day gifts with a short message on the back.
- Dutch-themed decor and tulip festival souvenirs.
- Florists' gift tags tied to bouquets.
Questions about this file
Can I paint the tulip in real tulip colours?
Yes. Paint over the engraved bloom in red, pink or yellow and wipe back the highlights so they stay pale, then paint the stem green. A thin wash keeps the woodcut texture visible.
Why do some of the small light flecks disappear?
They are tiny areas inside a dark fill, and too much power or a soft focus burns into them. Lower the power slightly and check the focus.
Is it a good Mother's Day or Easter gift?
Tulips are one of the classic spring flowers, so it fits both. Engrave a short message or a name on the back and tie it to a gift box.
Can it be cut from coloured acrylic?
Yes. On red or pink acrylic the engraving turns frosted and the highlights stay glossy, which looks like a real petal sheen.
Is the curl at the top strong enough to hang from?
Yes, at full size in plywood the curl and loop are solid. Use a thin ribbon or a ring rather than a heavy hook.
Similar files
