VisualizationFlower Shape SVG, Five Petal Blossom Laser Cut File DXF, Kids Craft Paint Blank, Baby Shower Favor Tag
A simple, chunky flower with five broad, slightly pointed petals in solid engraving, split by small teardrop gaps of bare wood and wrapped around a large plain centre. At 90 × 95.3 mm (3.54 × 3.75 in) it has no narrow parts at all, and the 4 mm hole sits on the upper left petal.
- Formats
- SVG, DXF
- Size
- 90 × 95 mm (3.54 × 3.75 in)
- Parts
- 1
- Hanging hole
- 4 mm
- Cut length
- 0.33 m
- Engraving area
- 35.4 cm²
- Material
- 3 mm plywood, MDF or acrylic
- Est. time, 10 W diode
- 6 min 59 s
- Est. time, 40 W CO2
- 2 min 25 s
- Est. time, 100 W CO2
- 1 min 41 s
- Per 300 × 400 mm sheet
- 12 pcs
- Per 600 × 400 mm sheet
- 24 pcs
- Layers
- CUT (red), ENGRAVE (black)
- License
- CC0 1.0: free for personal and commercial use
Free account required to download
How to make it
- 01Open the file at its real size, 90 × 95.3 mm; the hanging hole should sit on the upper left petal.
- 02Decide whether you want dark petals or a plain blank, and switch the engrave layer on or off.
- 03For dark petals use an even fill engrave, then cut the scalloped edge, which needs no special care.
- 04Sand, paint the centre or the petals, and thread ribbon or baker's twine through the hole.
Bold shape, nothing fragile
This is a graphic, icon-like flower: five wide petals with soft points, each one a solid dark area. Where two petals meet, a small teardrop of bare wood drops in from the edge and separates them like the folds of a paper flower. The middle is a large plain circle, and a light rim runs round the scalloped edge. From a distance it reads as a cherry, plum or forget-me-not blossom, or simply as a flower symbol.
Lots of fill, short cut path
The petals cover most of the face, so this is an engraving job more than a cutting job. A 10 W diode spends an estimated 6 min 59 s on each blossom in 3 mm plywood; CO2 tubes are quicker, at 2 min 25 s (40 W) and 1 min 41 s (100 W). The smooth outline cuts in moments even on a weak diode, and there are no thin parts to snap. If the fill looks blotchy, the cause is usually glue or resin in the plywood rather than your settings, so choose a clean, even sheet. It also works as a cut-only blank: switch off the engraving and you get a plain flower shape for painting.
Who buys a simple blossom
- Parents and teachers: unpainted blanks for craft tables and paint-your-own kits.
- Baby shower and christening favours, painted pink, lilac or white with a date on the back.
- Spring wreath makers who need a sturdy flower that can be glued or wired.
- Cherry blossom season decor, painted pale pink with a darker centre.
Questions about this file
Can I cut it without the engraving as a blank?
Yes. Hide or delete the engrave layer and cut only the outline. You get a smooth flower blank in seconds, ready for paint, decoupage or glitter.
Is it suitable for children to decorate?
There are no spikes or thin parts. Sand the edges and the hole, soften the petal points with fine sandpaper, and use non-toxic paint if children will decorate it.
Which flower is it meant to be?
It is a generic five-petal blossom, so you can sell it as cherry, plum, apple or forget-me-not just by changing the paint colour.
Can I add a date or initials for a baby shower?
Engrave them on the back after cutting, or put a small monogram in the plain centre before you run the job.
How many blossoms fit per board?
Twelve on a 300 × 400 mm board and 24 on a 600 × 400 mm board, so a full batch of favours uses very little material.
Similar files
