VisualizationBaking Tool Organizer SVG, Three Tier Spatula and Measuring Spoon Holder Laser Cut File, Baking Supply Caddy DXF
A three-tier baking tool organizer: four slots at the back for sachets and sprinkle jars, a long middle row for measuring spoons and a long front row for spatulas and brushes, six compartments in all. The download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; it is 320 × 240 × 80 mm (12.6 × 9.45 × 3.15 in), is cut from 10 pieces, slopes down to a 40 mm front and fits together with tabs and slots. Free to download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 320 × 240 × 80 mm (12.60 × 9.45 × 3.15 in)
- Parts
- 10
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,201 × 416 mm
- Cut length
- 7.67 m
- Est. time, 10 W diode (3 mm)
- 25 min 34 s
- Est. time, 40 W CO2 (3 mm)
- 10 min 39 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Select the file for your plywood and cut one slot on scrap to make sure the tabs fit firmly.
- 02Cut the ten pieces and pencil-mark the taller of the two 320 mm cross dividers.
- 03Assemble base, back, sides and front, fit the taller cross divider behind the lower one, then add the three short dividers in the back tier.
- 04Smooth the edges, lacquer, and lay long tools in the two front rows and sachets and jars in the back slots.
Two long rows for long tools
Most baking boxes in this category cut everything into small cells. This one keeps two of its three rows open across the full 320 mm width, because spatulas and measuring spoons on a ring are long and awkward in small bins.
- Back tier: four slots made by three short dividers. In the photo they hold baking powder sachets, vanilla sugar sachets and three jars of nonpareils, candy hearts and gold sugar pearls.
- Middle row: one open trough, here with a set of pink measuring spoons lying flat.
- Front row: another open trough, lower still, with a silicone spatula and a silicone brush.
Two cross dividers at about 52 and 62 mm high make the steps between the 80 mm back and the 40 mm front.
Laser notes
Ten parts. The two cross dividers are both 320 mm long but differ in height, so mark the taller one. The 3 mm layout is 1201.2 × 416 mm and the base alone is 320 × 240 mm, so on smaller machines cut the base by itself and the rest across one or two more sheets.
For the 3 mm file: about 25 min 34 s on a 10 W diode, about 10 min 39 s on a 40 W CO2, about 5 min 07 s on a 100 W CO2. A diode cuts 3 mm in one or two passes; 5 and 6 mm take several.
Finish and selling ideas
Sand the long divider tops smooth so silicone tools do not snag. A coat of clear lacquer is enough.
This layout photographs nicely next to a stand mixer, which makes a strong listing image. It also works as a starter baking kit for a teenager: box, spatula, brush and spoons in one parcel.
Questions about this file
How long can the tools be?
The two open rows run almost the full 320 mm width inside, so spatulas, whisks and spoon sets up to about 300 mm long lie flat.
Why only two cross dividers and no front cells?
Leaving the front rows open is deliberate: long baking tools do not fit small cells, and the rows stay easy to clean.
Which plywood thickness should I choose?
3 or 4 mm suits the low 80 mm walls; 5 and 6 mm work but cut slower on a diode.
Can I make it in MDF and paint it?
Yes, MDF cuts cleanly with the matching file and takes paint well; seal it so it does not swell.
Can I hang the spatulas upright instead?
The rows are made for laying tools flat; for upright storage, a taller utensil caddy is a better fit.
Similar files
