VisualizationPantry Box SVG, Kitchen Storage Organizer DXF, Laser Cut Countertop Bin with Front Tray, Wooden Pantry Caddy
A laser cut file for a low pantry box with four back bays and a long, shallow strip across the front, for tea bags, napkins, small jars, toothpicks and baking cups. It includes SVG and DXF files for 3, 4, 5 and 6 mm plywood, an outer size of 340 × 220 × 90 mm (13.39 × 8.66 × 3.54 in), a sloped front, 9 tab-and-slot pieces and 5 compartments. The pantry box files are a free download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 340 × 220 × 90 mm (13.39 × 8.66 × 3.54 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,165 × 322 mm
- Cut length
- 7.18 m
- Est. time, 10 W diode (3 mm)
- 23 min 56 s
- Est. time, 40 W CO2 (3 mm)
- 9 min 58 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Pick the file that matches your plywood, then test-cut one slot and check the tab fit on scrap.
- 02Cut the nine parts: front, back, two sloped sides, base, the long cross divider and three back dividers.
- 03Join the sides and back to the base, add the front, set the cross divider, then press the three dividers into the back area.
- 04Sand, coat with lacquer or oil, and fill the back bays with tea, napkins and jars and the front strip with liners and skewers.
Four back bays and a front strip
A full-width cross divider leaves a long, shallow strip along the front of this box, and three dividers cut the back area into four bays. The strip is ideal for things that lie flat: in the photo, packs of paper cupcake liners and a bundle of wooden skewers. The back bays hold tea bags, a stack of printed napkins, two spice jars, and a cup of toothpicks with a roll of baker's twine. The walls are low, 90 mm at the back and 45 mm in front, so the box fits under wall cabinets.
Choosing the thickness
All four versions share the outer size; only the slot widths change. Three millimeter plywood is the quickest: about 23 min 56 s on a 10 W diode, about 9 min 58 s on a 40 W CO2 and about 4 min 47 s on a 100 W CO2, for the 3 mm file. A diode gets through 3 mm in one or two passes, while 5 and 6 mm need a stronger laser or several passes. The layout runs 1165.1 × 322 mm for 3 mm; on smaller beds, give the base and the long walls their own sheet.
Make it a set
This box pairs well with the deeper pantry organizers: use it on a shelf for baking extras and a bigger one on the counter for daily tea and coffee. Sand the edges, then wipe on clear lacquer or a hard wax oil so it cleans easily. The joints are tight enough without glue, and wood glue makes them permanent.
Selling ideas: a baking-supply box filled with liners and skewers for a home baker, a tea and napkin caddy for a café counter, or a rustic gift box for a farmhouse kitchen.
Questions about this file
What fits in the long front strip?
Flat or long items: cupcake liners, skewers, straws, sugar sachets or a pastry brush. It runs the full 340 mm width.
Will it fit under my wall cabinets?
With a 90 mm back wall it fits under most cabinets with plenty of room. Allow extra height for any jars that stand above the walls.
Can I cut it from MDF?
Yes, MDF works for a dry pantry box. Use the file that matches its thickness and seal or paint it so it does not stain.
Which thickness should I use?
Three millimeter is enough for light pantry items. Pick 4 or 5 mm if the box will be moved around a lot.
Can I add a word like PANTRY on the front?
The file has only cut lines, but you can add your own engraving layer on the front panel before cutting.
Similar files
