VisualizationBaking Supply Sorter SVG, Narrow Five Slot Sachet and Sprinkles Holder Laser Cut File, Slim Pantry Shelf Organizer DXF
A slim baking supply sorter, only 160 mm deep, with five upright full-depth slots for baking powder and vanilla sachets, stacked sprinkle jars, measuring spoons and pastry brushes. The download contains SVG and DXF files for 3, 4, 5 and 6 mm plywood; the sorter is 320 × 160 × 90 mm (12.6 × 6.3 × 3.54 in), cut from 9 pieces, with sides that slope down to a 45 mm front, and it assembles with tabs and slots. All eight files are a free download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 320 × 160 × 90 mm (12.60 × 6.30 × 3.54 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 984 × 262 mm
- Cut length
- 6.24 m
- Est. time, 10 W diode (3 mm)
- 20 min 48 s
- Est. time, 40 W CO2 (3 mm)
- 8 min 40 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Use the file that matches your plywood thickness and cut a single slot first to check the tab fit.
- 02Cut the nine parts; the four 160 × 90 mm dividers are identical and interchangeable.
- 03Assemble base, back, sides and the 45 mm front, then push the four dividers into their slots from the top.
- 04Sand the divider tops, finish with oil or lacquer, and give each slot one kind of baking supply.
Five slots in a row
At 160 mm deep, this is the slimmest baking organizer in the set. Four dividers run front to back and create five equal slots, each a little under 60 mm wide, and there are no cross dividers. Everything stands upright and leans slightly back against the sloped sides, like files in a desk sorter.
The photo shows one item type per slot, left to right:
- baking powder sachets
- vanilla sugar sachets
- three sprinkle jars stacked from back to front
- a set of nested measuring spoons
- two silicone pastry brushes, pink and cream
The 45 mm front against a 90 mm back gives a steep slope, which is why the sachets fan out so you can read the top of each one.
Fits where deeper boxes do not
The narrow depth suits a windowsill, a shallow shelf above the counter, or the gap at the back of a worktop. Put two of them end to end along a shelf and you have ten slots in a 640 mm run.
Laser and finishing notes
Nine parts: front, back, two sides, base and four identical 160 × 90 mm dividers. The 3 mm layout is 984 × 262 mm, so on a smaller bed you can cut the base and back first and the rest in a second job. For the 3 mm file allow about 20 min 48 s on a 10 W diode, about 8 min 40 s on a 40 W CO2 and about 4 min 10 s on a 100 W CO2. Plan extra passes for 5 and 6 mm on a diode.
Thinner plywood leaves wider slots, so 3 or 4 mm is the better choice here. Sand, then seal with clear oil. As a gift for a baker it pairs nicely with a set of pastry brushes and spoons.
Questions about this file
How wide is each slot?
Each of the five slots is a little under 60 mm wide inside, enough for a stack of sachets, a line of small jars or a pair of brushes.
Will it fit on a narrow shelf?
Yes, it is only 160 mm (6.3 in) deep, which fits most open shelves and windowsills.
Can I make it longer with more slots?
Extend the base, front and back and add dividers at the same spacing; keep every slot equal to your sheet thickness so the tabs still fit.
Which thickness leaves the most space?
3 mm plywood, since thicker dividers eat into the slot width; 4 mm is a good compromise for strength.
Can I use it for tea or office supplies?
Yes, the upright slots work just as well for tea sachets, envelopes or notepads.
Similar files
