VisualizationMakeup Organizer With Front Tray SVG, Low Front Cosmetic Holder Laser Cut File, Wooden Vanity Organizer DXF
A free laser cut makeup organizer, 320 × 180 × 90 mm (12.60 × 7.09 × 3.54 in), with four slots across the back and one long open tray at the front. SVG and DXF files are included for 3, 4, 5 and 6 mm plywood; the 9 pieces fit together with tabs and slots, and the front wall is only 45 mm high, the lowest in this series. Free to download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 320 × 180 × 90 mm (12.60 × 7.09 × 3.54 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,020 × 282 mm
- Cut length
- 6.31 m
- Est. time, 10 W diode (3 mm)
- 21 min 02 s
- Est. time, 40 W CO2 (3 mm)
- 8 min 46 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Pick the file for your sheet and check the fit of one back divider in a test slot.
- 02Cut the nine parts from the 1020 × 282 mm layout, placing the 320 mm base on a separate sheet if needed.
- 03Attach the three dividers to the cross divider, set them in the base, then add the back wall, the sides and the 45 mm front.
- 04Sand, coat with water-based polyurethane, and put daily items in the open front tray.
Four slots behind, one open tray in front
The back row is cut into four bays by three short dividers, each about 8 cm wide, which suits brushes, lipsticks, a cushion compact and a palette standing on edge. In front of the 64.9 mm cross divider there is a single tray running the full 320 mm, with no dividers at all. That is where you put the things you reach for every morning: powder, blush and an eyeshadow palette lying flat, as on the marble bathroom counter in the photo.
Why the front is so low
The front wall is just 45 mm against a 90 mm back, so the sides fall steeply. Items in the long tray are easy to grab with one hand and you see their lids from above, which makes this layout handy for a daily routine rather than for storage.
Laser settings, sheet size and assembly
The layout is 1020 × 282 mm; a smaller bed will need the base on its own sheet. Cutting the 3 mm file takes about 21 min 02 s on a 10 W diode, about 8 min 46 s on a 40 W CO2 and about 4 min 12 s on a 100 W CO2. Run a single slot test first: if the tabs are loose, lower the kerf offset rather than switching thickness.
Fit the three back dividers onto the cross divider, press the assembly into the base, then add the back, sides and the 45 mm front. Glue is optional. Sand the edges and use a water-based polyurethane if it sits by a basin, because the long tray collects drips.
Good gift fillers: a cotton pad jar, a set of brushes and two lip colors.
Questions about this file
What fits in the long front tray?
Flat items: pressed powder, blush compacts, eyeshadow palettes, a small mirror or a row of lipsticks lying down. It is open from end to end, with no dividers.
Can I add dividers to the front tray?
Yes, copy one of the back dividers in your editor, shorten it to the 64.9 mm cross-divider height and add matching slots to the base and cross divider.
Is 45 mm too low to hold things in?
It keeps compacts and palettes in place and stops lipsticks rolling off. Tall bottles belong in the back slots.
How long does the 6 mm version take to cut?
Only the 3 mm time is estimated; thicker sheet cuts slower, and a 10 W diode will need several passes for 6 mm.
How do I keep foundation drips from staining it?
Seal the tray before use with water-based polyurethane or hardwax oil, two coats on the inside floor. Wipe spills right away.
Similar files
