VisualizationLow Makeup Tray SVG, Six Cell Vanity Organizer Laser File, Under Mirror Cosmetic Tray Wooden DXF
A free download for a low makeup tray with six cells in two rows of three, 300 × 200 × 90 mm (11.81 × 7.87 × 3.54 in). It consists of 10 plywood parts with tab-and-slot joints, the sides slope from a 90 mm back to a 50 mm front, and the SVG and DXF files are prepared for 3, 4, 5 and 6 mm plywood.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 300 × 200 × 90 mm (11.81 × 7.87 × 3.54 in)
- Parts
- 10
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,034 × 302 mm
- Cut length
- 6.74 m
- Est. time, 10 W diode (3 mm)
- 22 min 28 s
- Est. time, 40 W CO2 (3 mm)
- 9 min 22 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Pick your thickness, then test one front-row divider in a scrap slot.
- 02Cut the ten parts from the 1034 × 302 mm layout on two sheets if needed.
- 03Fix the four short dividers to the 69.7 mm cross divider, taller ones at the back, set the grid in the base and add back, sides and the 50 mm front.
- 04Smooth the cell edges, oil the tray and sort brushes and palettes at the back, lipsticks and compacts at the front.
Six cells, kept low
The layout matches the tall six-cell box, but everything is lower: a 90 mm back, a 50 mm front and a 69.7 mm cross divider. That makes it the better choice under a wall mirror, inside a deep drawer or on a shelf with little headroom. Two short dividers per row give three cells at the back and three at the front, each about 10 cm wide. On the wooden vanity in the photo the back row holds brushes and two eyeshadow palettes, and the front row keeps lipsticks, a powder compact and a blush apart.
Cutting it
The 3 mm layout measures 1034 × 302 mm, and the thicker files are a few millimetres longer. On a desktop laser split it over two sheets, keeping the four short dividers together so they are easy to sort. The 3 mm file is estimated at about 22 min 28 s for a 10 W diode, about 9 min 22 s for a 40 W CO2 and about 4 min 30 s for a 100 W CO2. A 10 W diode needs one or two passes for 3 mm; the 5–6 mm versions are better left to a stronger laser or several passes.
Building, finishing and gifting
Attach the two back-row dividers (90 mm) and the two front-row dividers (69.7 mm) to the cross divider, place the grid in the base, add the back and sides, and finish with the front. The tray holds together without glue. Sand the cell edges where fingers reach in and apply clear oil.
It makes a tidy drawer insert for a dressing table, a gift for a new apartment, or a bundle item with a small mirror. Because it is low, it also stacks neatly in a box for shipping.
Questions about this file
Will it fit inside a dresser drawer?
If the drawer has at least 9 cm of clear height and is 30 × 20 cm inside, yes. The low front makes it easy to reach in from above.
Low or tall six-cell box: which should I cut?
Cut this 90 mm version for drawers and spots under a mirror. The 100 mm version hides long brush handles better on an open counter.
Can it be made from acrylic?
Yes, with the file matching the acrylic thickness. Frosted acrylic makes a clean drawer insert that is easy to wipe.
Do I need clamps when gluing?
No, the tabs hold the parts in position while wood glue dries. Just wipe off any squeeze-out with a damp cloth.
How do I personalize it?
Engrave a name or a small pattern on the front panel before assembly. The file has no engraving, so you add the layer yourself.
Similar files
