VisualizationBaking Supply Tray SVG, Low Profile Baking Organizer Laser Cut File, Measuring Spoon and Sprinkles Holder DXF
A low baking supply tray with four slots at the back for sachets, sprinkle jars and pastry brushes and one long front trough for measuring spoons and cups, five compartments in all. The download has SVG and DXF files for 3, 4, 5 and 6 mm plywood; the tray is 300 × 220 × 80 mm (11.81 × 8.66 × 3.15 in), uses 9 pieces, slopes down to a 36 mm front and assembles with tabs and slots. Free to download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 300 × 220 × 80 mm (11.81 × 8.66 × 3.15 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,060 × 312 mm
- Cut length
- 6.60 m
- Est. time, 10 W diode (3 mm)
- 22 min 00 s
- Est. time, 40 W CO2 (3 mm)
- 9 min 10 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Select the 3, 4, 5 or 6 mm file and test a single tab and slot on scrap from the same sheet.
- 02Cut the nine parts: front, back, two sides, base, the long cross divider and three identical short dividers.
- 03Assemble the base, back, sides and low front, slide the cross divider in, then add the three short dividers behind it.
- 04Sand, seal with clear lacquer, and lay measuring tools in the front trough and sachets and jars in the back slots.
Low walls and a long trough
At 80 mm high with a front of only 36 mm, this is one of the lowest boxes in the baking set. It fits under a cabinet shelf or inside a deep drawer, and everything in it can be seen from above.
A single cross divider runs the full 300 mm width. Behind it, three dividers make four slots: in the photo one holds baking powder sachets, the next vanilla sugar sachets, the third four small jars of sprinkles and candy hearts, and the last two silicone pastry brushes standing up. In front of the cross divider there is no division at all, just one long trough. That trough is the reason to pick this tray: a full set of nested measuring spoons on a ring lies flat in it, and so would a whisk, a piping bag or a long spatula.
Cutting and assembly tips
Nine parts in total. The three back dividers are all 132.6 mm long and interchangeable, which makes assembly quick. The 3 mm file is laid out on 1060 × 312 mm; on a smaller laser, cut the base alone and the walls and dividers in a second job.
On a 10 W diode the 3 mm file takes about 22 min 00 s, on a 40 W CO2 about 9 min 10 s and on a 100 W CO2 about 4 min 24 s. For thicker plywood, add passes or switch to a CO2. Because the walls are so low, 3 or 4 mm plywood looks most in proportion.
Make it a set
Cut it twice and keep one for decorating supplies and one for bread baking tools. A painted front in a soft color matches pastel mixers, and the low profile slides into a pantry shelf next to flour canisters.
Questions about this file
What fits in the long front trough?
Measuring spoon and cup sets, a small whisk, piping tips in a bag or a bench scraper; anything flat up to about 290 mm long.
Will it fit in a kitchen drawer?
At 80 mm tall it fits most deep drawers; check that your drawer is at least 220 mm deep inside.
Which thickness should I use?
3 or 4 mm suits the low walls best visually; 5 and 6 mm work but make the tray look heavier.
Can I make it in MDF?
Yes, use the file for your MDF thickness. MDF takes paint well if you want a colored tray.
Can I engrave the slots with labels?
The file has no engraving, but you can add small labels such as Vanilla or Sprinkles on the back wall in your laser software.
Similar files
