VisualizationSnack Organizer SVG, 4 Slot Pantry Snack Bin Laser Cut File, Granola Bar Holder, Wooden Snack Station DXF
A four-lane snack organizer that keeps single-serve packs of granola bars, nuts, dried fruit and crackers standing in rows. It is provided as SVG and DXF with separate files for 3, 4, 5 and 6 mm plywood, measures 320 × 200 × 100 mm (12.60 × 7.87 × 3.94 in) and is cut from 8 pieces, with three full-depth dividers forming 4 compartments. The sides slope to a 55 mm front, it assembles with tabs and slots, and the file is a free download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 320 × 200 × 100 mm (12.60 × 7.87 × 3.94 in)
- Parts
- 8
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,060 × 312 mm
- Cut length
- 6.20 m
- Est. time, 10 W diode (3 mm)
- 20 min 40 s
- Est. time, 40 W CO2 (3 mm)
- 8 min 37 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Download the file for your plywood thickness and cut one divider and slot from scrap to check how tight it is.
- 02Cut the eight parts; the three dividers are the same, so stack them together after cutting.
- 03Fit both sloped sides into the base, add the back, push in the three dividers and finish with the 55 mm front.
- 04Sand and finish, then stand snack packs upright in the four lanes, one type per lane.
Four lanes of snacks
Three full-height dividers split the box into four equal lanes about 75 mm wide and 200 mm deep. Snack packs stand in them like cards in a recipe box, leaning back against the slope so every wrapper shows. Our photo runs granola bars on the left, then mixed nut packs, dried cranberry and apricot packs, and square cracker packs on the right. The 100 mm back wall supports tall wrappers, and the 55 mm front lets kids grab one pack without tipping the rest.
Cut and assemble
The file has eight parts: front, back, two sloped sides, base and three identical dividers. The 3 mm layout is roughly 1060 × 312 mm, so on a smaller bed separate the base from the walls and cut in two rounds. The 3 mm file takes about 20 min 40 s on a 10 W diode, about 8 min 37 s on a 40 W CO2 and about 4 min 08 s on a 100 W CO2. A diode gets through 3 mm in one or two passes; the 5 and 6 mm files call for a CO2 or several passes. For snacks, 3 mm is fine, and 4 mm is better if the box will travel to the office full.
Join the sides to the base, add the back wall, slide in the three dividers and close the front. Dry fit first; once you are happy, a few drops of wood glue make it permanent.
Finishing and selling ideas
Sand the divider tops and give the box a coat of clear lacquer or oil so sticky fingers wipe off. Snack stations appeal to parents, offices and holiday rental hosts. Offer it with the word snacks engraved on the front, in a set with a matching bag organizer, or filled with treats as a teacher or coworker gift.
Questions about this file
What snacks fit in the lanes?
Each lane is about 75 mm wide, so granola bars, nut packs, cracker packs and fruit pouches stand upright. Larger chip bags are better in a two-bay bin.
Can I scale it up for bigger snack bags?
Enlarge the outline in your software but keep slot and tab widths equal to your sheet thickness, because uniform scaling breaks the joints.
Plywood or MDF for a snack box?
Birch plywood is lighter and looks warmer on a counter; MDF is fine if you plan to paint it in a bright color.
Does it need a food-safe finish?
Snacks stay in sealed packs, so any clear finish works. If you plan to put loose food in it, use a food-safe oil and let it cure fully.
Should the dividers be glued?
They sit firmly in their slots without glue; a drop on each tab stops them lifting when packs are pulled out quickly.
Similar files
