VisualizationPantry Snack Organizer SVG, Granola Bar Lane Snack Tray Laser File, Wooden Snack Caddy, Kitchen Snack Box DXF
A pantry snack organizer with a full-depth center lane for rows of bars and two side columns, each split into a back and front cell, for nut, fruit and cracker packs. It is supplied as SVG and DXF with separate files for 3, 4, 5 and 6 mm plywood, measures 340 × 260 × 100 mm (13.39 × 10.24 × 3.94 in), and is cut from 9 pieces into 5 compartments. The sides slope to a 55 mm front, it assembles with tabs and slots, and it is free to download.
- Formats
- SVG, DXF
- Outer size (W × D × H)
- 340 × 260 × 100 mm (13.39 × 10.24 × 3.94 in)
- Parts
- 9
- Material thickness
- 3, 4, 5 or 6 mm plywood (a file for each)
- Layout size (3 mm file)
- 1,220 × 372 mm
- Cut length
- 7.29 m
- Est. time, 10 W diode (3 mm)
- 24 min 19 s
- Est. time, 40 W CO2 (3 mm)
- 10 min 08 s
- Layers
- CUT only, no engraving
Free account required to download
How to make it
- 01Pick the file for your plywood thickness and test one cross divider in a scrap slot.
- 02Cut the nine parts, splitting the 1220 × 372 mm layout across sheets on a smaller machine.
- 03Assemble base, sides and back, slide in both long dividers, add a cross divider to each side column, and fit the front.
- 04Sand and seal, line up bars in the center lane and fill the four side cells with packs.
A long lane for bars
The center lane runs the whole 260 mm depth, the deepest base in the snack group. Bars line up in it in rows, one flavor behind another: in the photo, green-wrapped bars at the back, then chocolate bars, then nut bars at the front. Each side column is split by a cross divider about 75 mm tall into two cells about 104 mm wide. On the left, nut packs sit behind dried apricots; on the right, crackers sit behind dried cranberries. That makes five compartments, with the most popular snacks in the middle where everyone reaches first.
Cutting and building
The file has nine parts: front, back, two sloped sides, base, two long dividers and two identical cross dividers. The 3 mm layout measures about 1220 × 372 mm, so most desktop lasers will need two or three sheets. Times for the 3 mm file: about 24 min 19 s on a 10 W diode, about 10 min 08 s on a 40 W CO2, about 4 min 52 s on a 100 W CO2. 3 mm is enough for this load and a diode cuts it in one or two passes; 5 and 6 mm need a CO2 or extra passes.
Fit sides and back to the base, add the two long dividers, drop the two cross dividers into the side columns, and close with the 55 mm front. A dry fit holds; glue makes it permanent.
Finishing and selling ideas
Sand the lane edges and seal with oil or lacquer. Lead your listing with the bar lane, because shoppers looking for granola bar or protein bar storage want exactly that. It pairs well with a bag organizer for a kitchen set, and an engraved family name on the front makes a good custom option.
Questions about this file
How many bars fit in the center lane?
The lane is the full 260 mm deep, so several rows of standard granola or protein bars fit one behind another.
Are the two side columns the same?
Yes, both cross dividers are the same size, so the left and right columns match, each with a back and a front cell.
Can I scale it for a bigger pantry?
Enlarge the outline but keep every slot at the thickness of your plywood; scaling the slots too leaves the tabs loose.
Is MDF a good option?
Painted MDF works well if you want a colored pantry box. Seal it so humidity does not swell the edges.
How do I finish it for a pantry?
A hardwax oil or clear water-based lacquer is enough; pantry snacks stay wrapped, so the finish mainly protects against fingerprints.
Similar files
